Danfoss VZH052 Series Скачать руководство пользователя страница 42

Страница: 42 / 54

GENER

AL INFORMA

TION

ODUC

T INFORMA

TION

STEM DESIGN

ORDERING INFORMA

TION

INTEGR

ATION INT

O SY

STEM

Assembly line procedure

Compressor holding

charge

Handling

Compressor storage

Each compressor is shipped with a nominal dry
nitrogen holding charge between 0.3 and 0.7 bar
(4 psi and 10 psi) and is sealed with elastomer
plugs.

Respect the following sequence:

•

Remove the nitrogen holding charge via the

suction Schrader valve to avoid an oil mist blow
out.

•

Remove the suction plug first and the discharge

plug afterwards to avoid discharge check valve
gets stuck in open position.
An opened compressor must not be exposed to
air for more than 20 minutes to avoid moisture is
captured by the PVE oil.

Each Danfoss VZH scroll compressor is
equipped with one lift ring on the top shell.
• Always use one lift ring and discharge tube

when lifting the compressor.

• Use lifting equipment rated and certified for

the weight of the compressor or compressor
assembly.

• A spreader bar rated for the weight of the

compressor is highly recommended to ensure a
better load distribution.

• The use of lifting hooks closed with a clasp is

recommended.

• Never use the lift rings on the compressor to lift

the full unit.

Maintain the compressor in an upright position
during all handling manoeuvres (maximum of
15° from vertical).

- Store the compressor where is not exposed to
rain, corrosive or flammable atmosphere.

- Store the compressor between
-35°C and 70°C (-31°F and 158°F) when it is
charged with nitrogen.

- Store the compressor between -35°C and 55°C
(-31°F and 131°F) when it is charged with R410A
refrigerant.

HEAVY

do not lift

manually

AB237586440343en-000601

Содержание VZH052 Series























































Результаты поиска

Содержание VZH052 Series

Отзывы:

Danfoss VZH052 Series, Руководство пользователя, Страница: 42 / 54

Результаты поиска

Содержание VZH052 Series

Отзывы: