Danfoss VLT Center Winder MCO 352 Скачать руководство пользователя | Manualshive

Страница: 15 / 38

background image

Input 37 Safe Stop

Option:

Function:

Terminal 37 must be closed for the frequency converter to run. If this input is opened while running
the frequency converter will coast to a stop.

Output O1 End of Roll Indicator

Option:

Function:

This output turns ON to indicate that the diameter has reached the value programmed in parameter
19-12. This output turns OFF when Diameter is reset (Input 8) to a value in normal operating range.

Output O2 TLD Indicator

Option:

Function:

This output is turned ON when the Tension Limit Detector has sensed that tension has been out of
range as set in parameters 19-08 and 19-09 for the number of scans set in parameter 19-10. A
Tension Limit results in a Winder fault. Turning the tension OFF resets this fault and the output.

Output O3 Running on Tension

Option:

Function:

This output is turned ON when the winder is regulating tension. The output is turned OFF when
tension is switched off or if there is a station fault. Turning the tension OFF resets this fault and the
output.

Output O4 Ready

Option:

Function:

This output is turned ON when the station is ready to run. The output turns OFF if there is a TLD
fault, an FC Alarm, an MCO 305 Error, Commanded Quick Stop, or Commanded Coast. Note: Outputs
5-8 are not used.

Relay 01 Running on Tension

Option:

Function:

This relay output (01, 02, 03) is energized when the winder is regulating tension. The relay output
is de-energized when tension is switched off or if there is a station fault.

NB!

Parameter 5-40 must be set for MCO controlled [51] for this function to work as described.

Relay 02 Ready

Option:

Function:

This relay output (04, 05, 06) is energized when the station is ready to run. The relay will de-energize
on a TLD fault, an FC Alarm, an MCO 305 Error, Quick Stop, or Coast.

VLT

®

Center Winder MCO 352

4 How to Install

MG.33.T1.02 - VLT

®

is a registered Danfoss trademark

15

4

«
...
13
14
15
16
17
...
»

Содержание VLT Center Winder MCO 352







































Отзывы:

Нет отзывов

Похожие инструкции для VLT Center Winder MCO 352

Бренд: ABB Страницы: 52

Бренд: Mamas & Papas Страницы: 16

Бренд: Abus Страницы: 12

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Oldham Страницы: 32

Бренд: H3C Страницы: 14

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

SHERPA MONOBLOC B0812

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 16

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды