5-30 Terminal 27 Digital Output
Option:
Function:
[181]
Prev. Maintenance
[182]
Deragging
[188]
AHF Capacitor Connect
[189]
External Fan Control
[190]
No-Flow
[191]
Dry Pump
[192]
End Of Curve
[193]
Sleep Mode
[194]
Broken Belt
[195]
Bypass Valve Control
[198]
Drive Bypass
[199]
Pipe Filling
[200]
Full capacity
[201]
Pump 1 running
[202]
Pump 2 running
[203]
Pump 3 running
[204]
Pump 4 running
[205]
Pump 5 running
[206]
Pump 6 running
[207]
Pump 7 running
[208]
Pump 8 running
[209]
Pump 9 running
5-50 Term. 29 Low Frequency
Range:
Function:
100
Hz
*
[0 - 110000
Hz]
Enter the low frequency limit
corresponding to the low motor shaft
speed (i.e. low reference value) in
5-52 Term. 29 Low Ref./Feedb. Value
. Refer
to .
This parameter is available for FC 302
only.
5-51 Term. 29 High Frequency
Range:
Function:
100 Hz
*
[0 - 110000
Hz]
Enter the high frequency limit
corresponding to the high motor shaft
speed (i.e. high reference value) in
5-53 Term. 29 High Ref./Feedb. Value
.
This parameter is available for FC 302
only.
5-52 Term. 29 Low Ref./Feedb. Value
Range:
Function:
0.000
*
[-999999.999 -
999999.999 ]
Enter the low reference value limit for
the motor shaft speed [RPM]. This is
also the lowest feedback value, see
also
5-57 Term. 33 Low Ref./Feedb.
Value
. Set terminal 29 to digital input
(
5-02 Terminal 29 Mode
=
[0] input
(default) and
5-13 Terminal 29 Digital
Input
= applicable value).
5-52 Term. 29 Low Ref./Feedb. Value
Range:
Function:
This parameter is available for FC 302
only.
5-53 Term. 29 High Ref./Feedb. Value
Range:
Function:
100
*
[-999999.999 -
999999.999 ]
Enter the high reference value
[RPM] for the motor shaft speed
and the high feedback value, see
also
5-58 Term. 33 High Ref./Feedb.
Value
.
5-54 Pulse Filter Time Constant #29
Range:
Function:
100
ms
*
[1 - 1000
ms]
Enter the pulse filter time constant. The
pulse filter dampens oscillations of the
feedback signal, which is an advantage, if
there is a lot of noise in the system. A high
time constant value results in better
dampening but also increases the time
delay through the filter.
5-60 Terminal 27 Pulse Output Variable
Option:
Function:
[0]
No operation
Select the desired display output for
terminal 27.
[45]
Bus ctrl.
[48]
Bus ctrl., timeout
[100] Output freq. 0-100
[101] Reference Min-Max
[102] Fe-200%
[103] Motor cur. 0-Imax
[104] Torque 0-Tlim
[105] Torque 0-Tnom
[106] Power 0-Pnom
[107] Speed 0-HighLim
[108] -160%
[109] Out frq 0-Fmax
[113] Ext. Closed Loop 1
[114] Ext. Closed Loop 2
[115] Ext. Closed Loop 3
[116] Cascade Reference
5-62 Pulse Output Max Freq #27
Range:
Function:
5000 Hz
*
[0 - 32000 Hz] Set the maximum frequency for
terminal 27, corresponding to the
output variable selected in
5-60 Terminal 27 Pulse Output Variable
.
5.1.1 Cascade CTL Option, 27-**
Cascade Control Option parameter group.
Parameter Descriptions
VLT
®
AQUA Drive MCO 101/MCO 102
24
MI38C402 - VLT
®
is a registered Danfoss trademark
5
5
