Danfoss H1P 045 Скачать руководство пользователя страница 31

Страница: 31 / 69

This section provides troubleshooting steps to follow if you are having problems with your machine until

you solve the problem. Some of the troubleshooting items are system specific. Always observe the safety

precautions listed in the Introduction section and precautions related to your specific equipment.

High Inlet Vacuum

High inlet vacuum causes cavitation which can damage internal pump components.

Unintended Machine Movement

Unintended movement of the machine or mechanism may cause injury to the technician or bystanders.

Secure the machine or disable/disconnect the mechanism while servicing to protect against unintended

movement.

Fluid Under Pressure

Escaping hydraulic fluid under pressure can have sufficient force to penetrate your skin causing serious

injury and/or infection. This fluid may also be hot enough to cause burns.

Relieve pressure in the system before removing hoses, fittings, gauges, or components. Never use your

hand or any other body part to check for leaks in a pressurized line. Use caution when dealing with

hydraulic fluid under pressure. Seek medical attention immediately if you are cut by hydraulic fluid.

Hazardous Material

Hydraulic fluid contains hazardous material.

Avoid prolonged contact with hydraulic fluid. Always dispose of used hydraulic fluid according to state,

and federal environmental regulations.

Electrical Troubleshooting

Electrical troubleshooting

Item

Description

Action

Control operates pump in

one direction only.

Control coil failure

•

Measure resistance at coil pins. Resistance should be

14.20 Ω (24V) or 3.66 Ω (12V) at 20°C [70°F].

•

Replace coil.

No pump function

No power to controller

Restore power to controller.

Erratic pump function

Electrical connection to pump is bad.

Disconnect connection, check wires, reconnect wires.

Filter bypass indicator switch Filter switch may be bad.

•

Check/replace filter switch.

•

Add gauge to filter bypass port to verify proper fluid flow

and verify switch operation by measuring resistance.

‒

Open resistance ≥ 510 Ω

‒

Closed resistance ≤ 122 Ω

Use a manual override to check proper pump operation and verify electrical problem, if available.

Service Manual

H1P 045/053/060/068 Axial Piston Single Pumps

Troubleshooting

Danfoss | June 2020

AX152886481964en-000405 | 31

Содержание H1P 045






































































Результаты поиска

Содержание H1P 045

Отзывы:

Бренды по названию

Популярные бренды

Danfoss H1P 045, Руководство по обслуживанию

Результаты поиска

Содержание H1P 045

Отзывы:

Бренды по названию

Популярные бренды