manualshive.com logo in svg

Danfoss EPU 2370, Инструкция по эксплуатации, Страница: 5 / 48

Поделиться
Скачать
Danfoss EPU 2370 Скачать руководство пользователя страница 5

BC-HM

VI.72.M4.02 

 Danfoss 11/97

5

Electrical connections and
wiring diagram

Connection to 230 VAC -
(terminals 13-24)
The control must be connected using the
terminal strips with screw terminals.

Up to 3 x 1.5 mm² or corresponding
wires can be connected in each
terminal. The terminal strips are coded
to prevent terminal strips with mains
voltage being connected to sensor
terminals.

Terminal

Load

Neutral (N) - 230 V~

13

Phase (L) - 230 V~

14

16 (close)

8(2)A 250V~

Reversible gear motor 230 V~, AMB, AMV etc.

17 (open)

8(2)A 250V~

Relay output R1 - 230 V~ (NC)

21 - 22

8(2)A 250V~

Relay output R2 - 230 V~ (NC)

23 - 24

8(2)A 250V~

Connections for sensors, etc. -
safety voltage (terminals 1 - 12)
Sensor mounting is described in the
instructions enclosed with the product.

Wire cross-section: min. 0.4 mm²
Total length of all sensor and BUS
wires: max. 150 metres.

Type

Terminal

S1

flow/duct (PI circuit)

ESMA/B/C/U

10  - 11

storage tank upper sensor

ESMB/U

S2

7 - 9

room sensor (P circuit)

ESMR

S3

frost protection sensor

ESMB/U/T

11 - 12

S4

return temperature sensor

ESMA/B/C/U

4 - 6

S5

external setpoint

ESME

4 - 5

storage tank lower sensor

ESMB/U

S6

8 - 9

compensation sensor

ESMR/T

External time switch/override

ECA 9010

3 - 4

Communication BUS

1 - 2

Note!
Wire resistance can give measurement
error. A resistance of 4 ohm

corresponds to a temperature increase
of about 1 degree.

Содержание EPU 2370

















































Отзывы:

Нет отзывов