Danfoss EPU 2370 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 48

Danfoss EPU 2370 Скачать руководство пользователя страница 10

10

VI.72.M4.02



Danfoss 11/97

BC-HM

g) Function selector

Control stopped, but system frost-
protected at 6 °C.
Time control not possible.

Constant reduced temperature.
The status of relay outputs depends
on the type of system selected.

Changeover between normal and
reduced temperature, as set on the
time switch.
The status of relay outputs depends
on the type of system selected.

Constant normal temperature.
The status of relay outputs depends
on the type of system selected.

Manual operation
All control functions inactive. The
control valve motor can be
operated manually with + and -
keys.
Relay outputs R1 and R2 can be
operated manually by pressing the
SET key (i) (see page 13).
The following combinations are
possible:

R1 (

I

)

R2 (

II

)

0

0

0

1

1

0

1

1

0 = open contact
1 = closed contact

In P0.0 the relay status and motor
function are displayed by horizontal
bars. A horizontal bar means
closed contact, see page 15, P0.0

«
...
8
9
10
11
12
...
»

Содержание EPU 2370

















































Отзывы:

Нет отзывов