manualshive.com logo in svg

Danfoss EM-PMI540-T2000, Руководство пользователя, Страница: 62 / 74

Поделиться
Скачать
Danfoss EM-PMI540-T2000 Скачать руководство пользователя страница 62

Make sure that the mating structure is not damaged. Do not pluck any bores or use at headed

bolts or rods for pushing the electric machine out of the mating structure.

For dismounting the electric machine, follow the Steps below.

1. Prepare the electric machine for lifting, for more information refer to Chapter 

Lifting

 on page 26.

Support the electric machine with lifting slings when dismounting.

2. Loosen the mounting bolts. For more information refer to Chapter 

Mounting the electric machine

 on

page 33.

3. If force is required, use the bores in D-end flange to push the electric machine out from the mating

structure, or use some other method that does not damage the electric machine.

4. Lift the electric machine off. Support the electric machine when lifting.

User Guide

EM-PMI540-T2000

Dismounting

 

62 | 

©

 Danfoss | July 2021

BC265857530809en-000202

Содержание EM-PMI540-T2000











































































Отзывы:

Нет отзывов