Danfoss 51 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 40

Danfoss 51 Series Скачать руководство пользователя страница 34

Legend (continued)

Item

Wrench size

Torque

M150, M151
(160, 1250)

10 mm internal hex

110 Nm [81 lbf•ft]

Item

Wrench size

Torque

M14

1 1/16

54 Nm [40 lbf•ft]

T4, T5, U6, U7

3 mm internal hex

3.7 Nm [2.7 lbf•ft]

N34, M22

1/4 internal hex

37 Nm [27 lbf•ft]

M23

3/8 internal hex

95 Nm [70 lbf•ft]

M24

1/8 internal hex

6 Nm [4.5 lbf•ft]

N84, N33

7/16 internal hex

12 Nm [9 lbf•ft]

Disassembly

1. Remove PCOR lock nut (M14).
2. Remove and discard O-ring (M16).
3. Remove the adjuster (Z*).
4. Remove the spring (M18).
5. Remove the PCOR spool assembly (M20).

C

Caution

Do not remove the PCOR valve bushing (M21).

6. Using a 7/16 wrench, remove the pin/plugs (N84) or (N33).
7. Remove and discard the O-rings (N84A) or (N33A).
8. Using a 1/8 internal hex wrench, remove 15 plugs (M24).
9. Remove and discard O-rings (M24A).

10. Using a 1/4 internal hex wrench, remove plugs (M22, N34).
11. Remove and discard O-rings (M22A, N34A).
12. Remove spool (N32).
13. Using a 3/8 internal hex, remove plug (M23). Discard O-rings (M23A).
14. Remove screws (M150 and M151) using a:

•

8mm internal hex wrench for 80 cc and 110cc motors

•

10 mm internal hex wrench for 160cc and 250cc motors

15. Remove the control assembly from the end cap.
16. Remove the 4-way valve assembly (F32).

C

Caution

Read

Series 51 and 51-1 Bent Axis Motors Service Manual

11008567 for minor repair instructions for the

4-way valve, threshold spring, and ramp spring components, if repair is necessary.

17. Remove and discard O-rings (F324).
18. Remove and discard O-rings (G38), (G36) and (G42) or the gasket (N240).
19. Using a 3 mm internal hex, remove orifices (T4, T6, U6, U7).

Inspection

1. Inspect the housing for signs of corrosion or damage.
2. Discard any damaged parts.

Service Manual

Series 51 Hydraulic Proportional Controls Service Manual

J1, J2, J3, J4 Controls

34

11009446 • Rev BA • July 2014

«
...
32
33
34
35
36
...
»

Содержание 51 Series









































Отзывы:

Нет отзывов