Danfoss 51 Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

Danfoss 51 Series Скачать руководство пользователя страница 31

Legend (continued)

Item

Wrench size

Torque

M18

4 mm internal hex

N/A

M10 (060, 080, 110)

8 mm internal hex

78 Nm [58 lbf•ft]

M10 (160, 250)

10 mm internal hex

110 Nm [81 lbf•ft]

Assembly

1. Lubricate and install O-rings (F324).
2. Install 4-way valve (F32).
3. Using petroleum jelly, lubricate and install O-rings (G38), (G36) and (G42) or install gasket (N240).
4. Install block (M1HC).
5. Install screws (M10) and washers (M11), if present.
6. Install spring (J10).
7. Install pin (M26). Install spring seat (M25).
8. Install the pilot piston (M24).
9. Install spring (M22). Install spring seat (M20)

10. Install gasket (M14). Install cover (M12).
11. Using a 4 mm internal hex wrench, install screws (M28). Torque to 6.4 Nm [4.7 lbf•ft].
12. Install adjustment screw (M18). Install locknut (M16).
13. Hold adjustment screw in place and torque locknut (M16) to 9 Nm [6.6 lbf•ft].
14. Slide shuttle spool (M44) into block.
15. Lubricate and install O-rings (M34A).
16. Using a 1/4-inch internal hex, install plugs (M34).
17. Install check ball (M47)
18. Install check ball seat (M46)
19. Lubricate and install O-ring (M48A).
20. Using a 1/4-inch internal hex, install plug (M48)
21. Using a 4 mm internal hex, install bleed valve (M38).
22. Using a 10 mm wrench, install locknut (M40).
23. Hold bleed valve in place and torque lock nut per table.

Service Manual

Series 51 Hydraulic Proportional Controls Service Manual

HC Controls

11009446 • Rev BA • July 2014

31

«
...
29
30
31
32
33
...
»

Содержание 51 Series









































Отзывы:

Нет отзывов