Danfoss 51 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

Danfoss 51 Series Скачать руководство пользователя страница 17

Legend

Item

Wrench size

Torque

N27

1/8 inch internal hex

7 Nm [4 lbf•ft]

N26

1/4 inch internal hex

37 Nm [28 lbf•ft]

N58
80cc, 110cc

8 mm internal hex

78 Nm [58 lbf•ft]

N58
160cc, 250cc

10 mm internal hex

110 Nm [81 lbf•ft]

Inspection

Clean and inspect components for damage or foreign material. Replace damaged parts.

Assembly

1. Lubricate and install new O-rings (N27A). Install plugs (N27) using a 1/8 inch internal hex wrench.

Torque to 7 N•m [4 lbf•ft].

2. Using petroleum jelly to retain them, install new interface O-rings (G36, G38, G42) or gasket (N240).
3. Position the multifunction block on the endcap. Install screws (N58). Torque screws as shown in the

table.

4. Lubricate and install the double-resolver spool (N30). The spool is symetrical, either end in first.
5. Lubricate and install new O-rings (N26A). Using a 1/4 inch internal hex wrench, install plugs (N26).

Torque to 37 N•m [28 lbf•ft].

Service Manual

Series 51 Hydraulic Proportional Controls Service Manual

Multifunction block

11009446 • Rev BA • July 2014

17

«
...
15
16
17
18
19
...
»

Содержание 51 Series









































Отзывы:

Нет отзывов