Danfoss 51 Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 40

Danfoss 51 Series Скачать руководство пользователя страница 20

Legend

Item

Wrench size

Torque

M18

1/8 internal hex

6 Nm [4 lbf•ft]

M12

5 mm internal hex

12 Nm [6 lbf•ft]

M16

1/4 internal hex

31 Nm [27 lbf•ft]

M22 (80, 110)

8 mm internal hex

78 Nm [58 lbf•ft]

M22 (160, 1250)

10 mm internal hex

110 Nm [81 lbf•ft]

Inspection

1. Inspect the housing and shuttle valve for damage or foreign material.
2. Check internal passages for contamination and clean them if necessary. If present, discard the 2

screens ( M14) (they are no longer necessary).

Assembly

1. If used, install the shuttle valve assembly (M10) (HZ controls only).
2. If used, install orifice (M12) using a 5 mm internal hex wrench (HZ controls only). Torque to 8 N•m [6

lbf•ft].

C

Caution

Overtorquing orifice (M12) may crush shuttle valve (M10).

3. Lubricate and Install new O-rings to all plugs.
4. Using a 1/4 inch internal hex wrench, install plugs (M16). Torque to 37 N•m [27 lbf•ft].
5. Using a 1/8 inch internal hex wrench, install plugs (M18). Torque to 6 N•m [4 lbf•ft].
6. Using petroleum jelly to retain them, install new O-rings (G36, G38, G42) or install gasket (G420).
7. Install the control housing onto the end cap.
8. Install screws (M22). Torque screws to:

•

78 N•m [58 lbf•ft] for 80 cc, and 110cc motors using an 8mm internal hex wrench.

•

110 N•m [81 lbf•ft] for 160cc and 250cc motors using a 10 mm internal hex wrench.

Service Manual

Series 51 Hydraulic Proportional Controls Service Manual

HZ, HA, HB, HE Controls

20

11009446 • Rev BA • July 2014

«
...
18
19
20
21
22
...
»

Содержание 51 Series









































Отзывы:

Нет отзывов