Dalsa Genie M640 Скачать руководство пользователя

Страница: 52 / 133



Operational Reference

Genie Monochrome Series-GigE Vision Camera

Synchronization Timing

Genie supports two types of sensor synchronization used to align the exposure to sensor timing:



Synchronous Mode

: Exposure is synchronous to the line timing of the sensor. Exposure granularity is 1µs and

the readout can be concurrent to the exposure for the fastest possible frame rate.



Reset Mode

: Timing is reset to initiate exposure of next frame. Exposure granularity is 1µs, but readout must

be sequential to exposure, reducing the maximum achievable frame rate.

Synchronous Mode



Synchronous mode starts the exposure period aligned to the sensor horizontal line timing and the programmable
duration granularity is 1µs.



In the case of the Genie M640, a horizontal line occurs every 31.77µs.



Exposure duration is from the sensor minimum (see Genie Sensor Overview) up to 16 sec.



In this mode, sensor exposure and sensor readout of the previous frame's exposure occur simultaneously. This
allows operating the sensor up to its maximum frame rate.



Any trigger received before the end of the exposure is ignored. The application can elect to receive messages
about ignored triggers. See

Events

" on page 69



Since the external trigger is asynchronous with the Genie horizontal line timing, the frame exposure start is
subject to 1 horizontal line jitter.

Synchronous Mode Timing example for Genie M640

Содержание Genie M640






































































































































Результаты поиска

Содержание Genie M640

Отзывы:

Похожие инструкции для Genie M640

Бренды по названию

Популярные бренды

Dalsa Genie M640, Руководство пользователя

Результаты поиска

Содержание Genie M640

Отзывы:

Похожие инструкции для Genie M640

Бренды по названию

Популярные бренды