Dalsa Genie M640 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 133

background image

Genie Monochrome Series-GigE Vision Camera

Installing the Genie Camera



21

Preventing Operational Faults due to ESD

Genie camera installations which do not protect against ESD (electrostatic discharge) may exhibit operational faults.
Problems such as random packet loss, random camera resets, and random loss of Ethernet connections, may all be
solved by proper ESD management.

The Genie camera when used with a simple power supply and Ethernet cable, is not properly connected to earth
ground and therefore is susceptible to ESD caused problems. An Ethernet cable has no ground connection and a
power supply's 0 volt return line is not necessarily connected to earth ground.

DALSA has performed ESD testing on Genie cameras using an 8 kilovolt ESD generator without any indication of
operational faults. The two following methods, either individually or together will prevent ESD problems.



Method 1: Use a shielded power supply cable where the shield is connected to earth ground at the supply end
and to the Hirose connector shell at the Genie end. The Genie case is now properly connected to earth ground
and can withstand ESD of 8 kilovolts, as tested by DALSA.



Method 2: Mount the Genie camera on a metallic platform which has a good connection to earth ground.

Sapera LT Library Installation

Note:

to install Sapera LT and the Genie device driver, logon to the workstation as an administrator or with an

account that has administrator privileges.

When Sapera application development is performed on the same computer that the Genie is connected to, the Sapera
Development Library (version 6.10 or later) must be installed. Else, Sapera LT is not required to control the Genie
camera.



Insert the DALSA Sapera CD-ROM. If

AUTORUN

is enabled on your computer, the DALSA installation

menu is presented.



If

AUTORUN

is not enabled, use Windows Explorer and browse to the root directory of the CD-ROM.

Execute

launch.exe

to start the DALSA installation menu and install the required Sapera components.



The installation program will prompt you to reboot the computer.



Continue with the Genie CD Package Installation described next.

Refer to

Sapera LT User’s Manual

concerning application development with Sapera.

«
...
21
22
23
24
25
...
»

Содержание Genie M640






































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genie M640

Бренд: Olympus Страницы: 2

Бренд: Olympus Страницы: 76

Бренд: Olympus Страницы: 76

Бренд: Olympus Страницы: 30

Бренд: Olympus Страницы: 83

Бренд: Olympus Страницы: 2

Бренд: Olympus Страницы: 120

Бренд: Olympus Страницы: 132

Бренд: Olympus Страницы: 84

Бренд: Olympus Страницы: 84

Бренд: Olympus Страницы: 80

Бренд: Olympus Страницы: 7

Бренд: Vantrue Страницы: 28

Бренд: Abus Страницы: 20

Бренд: Palsonic Страницы: 1

Бренд: Uniden Страницы: 20

Бренд: Boyo Страницы: 1

Бренд: Digi-Frame Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды