background image

2. Overview

The AMP-2500 DSP is a full rack width, 2U format 
two channel power amplifier rated at 500 Watts per 
channel. It is able to power up to four DALI CI SUB 
S-100 subwoofers simultaneously or one or two front 
or surround channel speakers. The AMP-2500 DSP 
provides four analogue inputs and one stereo S/PDIF 
digital input.

The AMP-2500 DSP is comprehensively equipped with 
DSP (digital signal processing) functions that enable 
it to be configured via the DALI PHANTOM CI AMP 
CONFIGURATOR with specific functional profiles 
designed for individual DALI speaker models.

The AMP-2500 DSP is by default set up with the DALI 
PHANTOM IW SUB S-100 functional profile installed. 
Installing profiles for alternative speakers is covered in 
Section 5 of this manual. DALI AMP-2500 DSP functional 
profiles for other speakers can be downloaded from: 

dali-speakers.com

2.1 DALI PHANTOM CI AMP 
CONFIGURATOR

The DALI PHANTOM CI AMP-2500 DSP provides 
comprehensive DSP based configuration menus 
accessible via the DALI PHANTOM CI AMP 
CONFIGURATOR web interface.

Access to the AMP CONFIGURATOR interface is made 
through wired (Ethernet) or wireless (WiFi) network 
connection to the AMP-2500 DSP either directly from a 
configuration device such as a smart phone or computer, 
or via a network router or switch.

The AMP CONFIGURATOR cover Speaker Profiles, 
Inputs, Outputs and General Settings and is described in 

Sections 5 

and

 8 

of this manual. Connecting the AMP-

2500 DSP to a wired or wireless configuration device or 
network is described in 

Section 5.2

.

2.2 Amplifier Connections 
and Power Switching

AMP-2500 DSP signal input and output connections 
are accomplished via RCA Phono and Euroblock 
style connectors. A GPIO (General Purpose In/Out) 
Euroblock connector enables some amplifier functions 
to be controlled externally, and wireless or RJ45 socket 
Ethernet network connection options are also provided. 
Cable connectors and connections are described and 
illustrated in 

Section 6

 of this manual. Connection and 

use of the GPIO socket is described in 

Section 5.5

.

AMP-2500 DSP amplifier incorporates a front panel 
mounted power button. Press the button once to switch 
the amplifier on or off. Amplifier power management 
behaviour can be configured via the Control web 
interface 

[Settings] Menu

 described in 

Section 5

 of this 

manual.

2.3 Firmware

This manual describes the features, functions and 
user interface of the AMP-2500 DSP amplifier running 

Firmware Version 1.3.3.

It is strongly recommended that the firmware version 
installed in the amplifier in use is checked initially, and 
regularly thereafter. If updated firmware is available, the 
amplifier should be updated as a priority.

The firmware installed in the amplifier can be identified 
and updated by selecting the 

[Device]

 option in the 

AMP CONFIGURATOR web interface 

[Settings] Menu

Firmware versions can be checked, and firmware 
downloaded, from the website: 

dali-speakers.com

5

Содержание PHANTOM CI AMP-2500 DSP






























Отзывы: