background image

9. Specifications

Frequency range

12 Hz – 20 kHz
(+/- 0.5 dB, 8 Ω load, 3 dB below rated power)

Connection input(s)

4x Analog unbalanced, RCA
4x Analog balanced, Euroblock connector
1x S/PDIF, RCA

Input impedance

10 kOhm

Output channels

2 x Lo-Z speaker (4 - 16 ohm)
1 x Hi-Z speaker (70V / 100V)
1x S/PDIF digital out, RCA

Maximum speaker cable cross section

2,5 mm

2

 / AWG 14 (Euroblock standard)

Output power @ 2 ohm

2 x 500 W  (SE) *

(BTL) **

Output power @ 4 ohm

2 x 500 W  (SE)
1 x 1000 W (BTL)

Output power @ 8 ohm

2 x 250 W  (SE)
1 x 1000 W (BTL)

Output power @ 70V

1 x 1000 W (BTL)

Output power @ 100V

1 x 1000 W (BTL)

Total system power

1000 W

Power consumption

350 W

Output voltage

45 Vrms (SE) - 90 Vrms (BTL)
70/100V (Hi-Z)

Output circuitry

UMAC™ Class D - full bandwidth PWM modulator with ultra-low distortion

Signal to noise-ratio

>108 dB
(A-weighted, 20 Hz - 20 kHz, 8 Ω load)

THD+N (typical)

< 0.05 %
(20 Hz - 20 kHz, 8 Ω load, 3 dB below rated power)

Other features:

Short circuit protection
DC protection
Undervoltage protection
Temperature protection
Overload protection
Rack mountable

Power supply

UREC™ universal mains switch mode power supply with Power Factor Correction (PFC) and standby 
converter

Operating temperature

0 - 40° C

Operating voltage/ frequency

Universal mains
100 V-240 V, 50 Hz-60 Hz

Power ratings

1 % THD @ 120 Vac and 230 Vac

Standby consumption

< 0.5 W

Outer dimensions (H x W x D)

88 x 440 x 332 mm
3.5 x 17.3 x 13.1 inches

Weight

5.9 kg
13 lb

Shipping weight

7.5 kg
16.5 lb

Accessories

2x Two channel balanced input connector
1x Two channel speaker output connector
1x GPIO socket connector
1x Mains power cable
4x Adhesive rubber feet
2x Rack mount ears (mounted)

Optional accessories

DALI CONNECT SC F222C (speaker cable)
DALI CONNECT SC F215C (speaker cable)

*SE – conventional, single ended output mode
**BTL – bridge-tied load output mode

29

Содержание PHANTOM CI AMP-2500 DSP






























Отзывы: