manualshive.com logo in svg

DALBO POWERCHAIN 800, Инструкция пользователя, Страница: 49 / 55

Поделиться
Скачать
DALBO POWERCHAIN 800 Скачать руководство пользователя страница 49

 

POWERCHAIN 

 

Page 49 

Changing the cylinder for tightening the disc chain 

Fig. 28 

1.

 

The disc harrow is folded out 

with the disc chains resting on 

the ground. 

2.

 

Check that the pressure has 

gone from the manometer so 

that the cylinder (A) is 

depressurised. 

3.

 

The hoses are disconnected from 

the cylinders. 

4.

 

Bolts, split pins and pins (B) are 

removed. 

5.

 

A new or repaired cylinder (A) is 

mounted. 

6.

 

Remember to install the split 

pins in the pins. 

 

 

 

After mounting, the tilt cylinder is activated until a small amount of movement can 

be felt in the cylinder. The cylinder is then activated in the opposite direction until 

the cylinder is back at the starting position. The cylinder is moved in this way a few 

times, whereupon the cylinder is moved out to the outer positions a few times to 

air the system out. 

 

 

Individuals must not be present within the action radius of the implement. 

Replacing the set of gaskets when tightening the disc chain 

Fig. 29 

 

8.

 

The cylinder is emptied of oil by carefully moving the piston back and 

forth. 

9.

 

Move the piston to the middle position, then unscrew the upper cap 

(pos. 3) from the cylinder tube (pos. 1). A special tool must be used to 

remove the cap. If the upper cap is very tight, this can be remedied by a 

little heating of the front of the upper cap. When the cap is unscrewed 

from the cylinder tube, pull the piston towards the cap. The piston rod can 

then be removed from the cylinder tube (pos. 1). 

10.

 

The lock nut (pos. 10) that is holding the sleeve (pos. 4) is disassembled. 

A 

(A) 

(A) 

A - A 

5 

3 

6 

7 

1 

2 

8 

9  10 

4 

Содержание POWERCHAIN 800
























































Отзывы:

Нет отзывов