DALBO POWERCHAIN 800 Скачать руководство пользователя страница 46

Страница: 46 / 55

POWERCHAIN

Page 46

Individuals must not be present within the action radius of the implement.

Replacement of the gaskets

Fig. 25

The cylinder is emptied of oil by carefully moving the piston back and

forth.

Move the piston to the middle position, then unscrew the upper cap

(pos. 3) from the cylinder tube (pos. 1). A special tool must be used to

remove the cap. If the upper cap is very tight, this can be remedied by a

little heating of the front of the upper cap. When the cap is unscrewed

from the cylinder tube, pull the piston towards the cap. The piston rod

can then be removed from the cylinder tube (pos. 1).

The lock nut (pos. 10) that is holding the sleeve (pos. 4) is disassembled.

The sleeve (pos. 4) is removed from the piston rod (pos. 2).

The cap (pos. 3) is pulled off the piston rod (pos. 2).

Remove the gaskets in the upper cap (pos. 5+6+7+8+9) and the sleeve.

All parts are checked for chips, burrs, etc. Check for rust around the

scraper ring (pos. 5) in the cap. If this is the case, remove it.

Mounting

New gaskets (pos. 5+6+7+8+9) are fitted in the cap and sleeve.

The thread on the cap (pos. 3) and the cylinder tube (pos. 1) are

lubricated with oil.

The cap (pos. 3) is mounted on the piston rod.

The sleeve (pos. 4) is fitted and the lock nut is screwed and

secured with

Loctite

. Make sure the thread is absolutely clean and free of oil and other

impurities before using Loctite.

Do not fill with oil within 12 hours of

using Loctite.

Lubricate the outermost seal on the sleeve that comes in contact with the

cylinder tube and the cylinder tube internally with oil and push the piston

into the middle position.

The cap is fitted on the cylinder tube and tightened.

To mount the cylinder, see “Changing of”.

(A)

A - A

9 10

Содержание POWERCHAIN 800
























































Результаты поиска

Содержание POWERCHAIN 800

Отзывы:

DALBO POWERCHAIN 800, Инструкция пользователя, Страница: 46 / 55

Результаты поиска

Содержание POWERCHAIN 800

Отзывы: