manualshive.com logo in svg
background image

 

- 5 - 

Installation

 

Select installation position 

 

 

 

 

 

1. If the unit is to be installed on the floor, its undercarriage should be heightened, to avoid 

ingression of accumulated water in rainy season. In snowy areas, it is important to prevent 

accumulated snow from blocking up the air

out. The recommended height is 20cm to 30cm.   

2. Drain ditch or other facilities should be arranged under the outdoor unit, to avoid the 

environment influence because of water discharge.   

3. To install the unit at balcony or top of building, the installation site must meet the allowable 

bearing capacity of building structure, without affecting the structural safety.   

4. Ensure the unit is well ventilated, direction of air exhaust is kept away from windows of 

neighboring buildings, and the exhaust air cannot flow back. Moreover, adequate service 

clearance should be kept around the unit.   

5. The unit should not be installed at places accompanied with oil, inflammable gas, corrosive 

components e.g. sulfur compound, or high

frequency equipment.   

6. 

The unit must be installed on reliable base or framework. Weight capacity of framework 

should be 3 times of the body weight, and safeguard measures should be taken to avoid 

malfunction of fastenings.   

7. The unit should not be installed at sites with typhoon/ earthquake hazards. Midair installation 

should be avoided as much as possible as machine falling down may result in severe accident.

   

 

 
 
 
 

Note!

Installation must be carried out by professional

 

Содержание DSP-85HA


















Отзывы: