background image

6-2  Example for the whole system

Power supply

Indoor unit

Indoor unit

Remote controller

Remote controller

Remote controller

Power supply

Outdoor unit

Main 
switch

Main 
switch

Power supply wiring

Transmission wiring

Circuit protection 
safety devices in 
accordance with local 
and national codes 

BS4Q unit

BS4Q unit

Cooling-dedicated 
indoor unit

6-3  Power circuit, safety device and cable requirements

• 

A power circuit (refer to Table 6) must be provided for connection of the unit. The circuit must be protected 
with safety devices in accordance with local and national codes i.e a fuse, a circuit breaker or a GFCI.

• 

When using residual current operated circuit breakers, be sure to use a high-speed type (0.1 second or 
less) 30mA rated residual operating current.

• 

Use copper conductors only.

• 

Use insulated wire for the power cord.

• 

Select the power supply cable type and size in accordance with relevant local and national regulations.

• 

Use vinyl cord with sheath or cable (2 wire) of AWG 18 - 16 for transmission wiring.

• 

The transmission wire lengths are as follows:

Between the Branch Selector unit and indoor units: Max. 3,280 ft. (1,000 m)
Between the Branch Selector unit and outdoor unit: Max. 3,280 ft. (1,000 m)
Between Branch Selector units: Max. 3,280 ft. (1,000 m)

Total wiring length: 6,560 ft. (2,000 m) or less

Table 6 

Units

Power supply

Model

Type

Hz

Voltage

Voltage range

Min.

Max.

MCA

MOP

BS4Q54TVJ

VJ

60

208/230

187

253

0.4

15

BS6Q54TVJ

0.6

BS8Q54TVJ

0.8

BS10Q54TVJ

1.0

BS12Q54TVJ

1.2

MCA: Minimum Circuit Ampacity (A); MOP: Maximum Overcurrent Protective Device (A)

NOTES 

• 

The above Table 6 of electrical characteristics refers to one Branch Selector unit.

12

3P405106-9 English

01_EN_3P405106-9.indb   12

3/27/2015   1:53:11 PM

Содержание VRV IV Series























Отзывы: