Daikin VHF Скачать руководство пользователя страница 32

Страница: 32 / 64

www.DaikinApplied.com 32

Vertical Stack WSHP • IM 986-11

nstallation

Installing The Return Air Panel Door

1 .

Install the return air panel door assembly (

Figure 40

Center, level and plumb the frame inside the framed

opening. Push the assembly into the opening until the

gaskets compress against the cabinet, and the frame face

is tight to the finished wall.

Notes:

1. Shims (field-supplied) should be used to make up the

space between the studs and the panel frame at the

locations of the fasteners on the panel frame (4).

Adhere them to the panel frame to keep them in

place (

Figure 40

2. Be sure the bottom flange of the door frame slides

beneath the cabinet flange, as shown in

Figure 40

This seal must compress between the bottom

panel flange and the bottom cabinet flange when the
installation of the panel door frame is complete.

2 .

Check that the panel door frame is centered within the

opening and seals completely to the cabinet return air

opening. Also confirm that the room side flange of the

frame is level, plumb and firmly against the drywall. Secure

the hinged panel door frame with the appropriate fasteners/

screws (field provided).

Note:

Before proceeding to instruction 3, be sure to clean

frame with rubbing alcohol to remove any oils or dust to

ensure a strong bond between velcro and door frame.

3 .

Remove the backing on the (hook) velcro strips and

firmly press the cover plate to the panel door frame in the

location shown in

Figure 40

Note:

The clearance holes along the top edge of the cover

plate should fit around the screws on the underside of

the top door frame.

Figure 40: Installing the return air panel door (hinged perimeter panel door shown)

Seal gasket

on the back of

the panel door

frame along top

and two sides

Door panel bot-

tom flange to

slide beneath

cabinet flange

Shims (field-supplied), make-up space between

framed opening and panel door frame.

Note:

If install-

ing the louvered panel door that will utilize the optional

outdoor air damper, remove the knockout for the

damper and keep the opening clear of obstruction.

Seal gasket on underside of cabinet flange. Door panel

flange slides underneath and compresses to cabinet

Cover plate

Содержание VHF

































































Результаты поиска

Содержание VHF

Отзывы:

Похожие инструкции для VHF

Бренды по названию

Популярные бренды

Daikin VHF, Руководство по установке и обслуживанию

Результаты поиска

Содержание VHF

Отзывы:

Похожие инструкции для VHF

Бренды по названию

Популярные бренды