background image

 

UK.PPC150

-

300(SL)/R32

 

 

November 

2022

—Version 2.1

 

Domestic hot water tank for Daikin Altherma Monobloc (R32)

 

 

 

1.2.3

 

Water

 

If applicable. See the installation manual or installer reference guide of your 
application for more information.

 

2

 

About the box

 

2.1

 

Overview: Above the box

 

It contains information about:

 

• 

Removing the accessories from the unit

 

Keep the following in mind:

 

• 

At delivery, the unit MUST be checked for damage. Any damage MUST be 
reported immediate to the carrier

s claims agent.

 

• 

Bring the packaged unit as close as possible to its final installation position to 
prevent damage during transport

 

• 

Prepare the path along which you want you bring the unit in advance.

 

3

 

Preparation

 

3.1

 

Overview: Preparation

 

This chapter described what you have to do and know before going on

-

site.

 

It contains information about:

 

• 

Preparing the installation site

 

• 

Preparing the water piping

 

• 

Preparing the electrical wiring

 

3.2

 

Preparing the installation site

 

The cylinder is to be installed vertically on a stable base which must be capable 
of supporting the weight when the cylinder is full of water.

 

The minimum recommended installation space is dependent on the 
specification of the cylinder, the slimline variants are recommended if available 
space is limited. Additional considerations should be made to allow space to 
mount expansion vessels. Full specification, weights and dimensions of the 
product range are provided in this booklet.

 

Access for maintenance of all equipment should be considered when position 
the unvented cylinder. Care should be taken that the immersion heater can be 
withdrawn for servicing if required, these are 375mm long. Building regulation 
G3 should always be followed when installing discharge pipework from the 
safety valves.

 

Any hot outlets which are higher than the cylinder will reduce in pressure by 0.1 
bar for every 1m of height difference.

 

All exposed pipe work should be insulated and additional considerations should 
be  taken to protect the unit from frost damage. Particular care is needed if the 
cylinder is to be installed in an exposed location such as an outhouse or garage.

 

NOTICE

 

Make sure water quality complies with EU Directive 98/93 EC.

 

1.2.4

 

Electrical

 

DANGER: RISK OF ELECTROCUTION

 

• 

Turn OFF all power supply before removing the switch box cover, 
connecting electrical wiring or touching electrical parts.

 

• 

Disconnect the power supply for more than 1 minute, and 
measure the voltage at the terminals of main circuit capacitors or 
electrical components before servicing. The voltage MUST be less 
than 50 V DC before you can touch electrical components. For 
the location of the terminals, see the wiring diagram.

 

• 

Do NOT touch electrical components with wet hands.

 

• 

Do NOT leave the unit unattended when the service cover is 
removed.

 

WARNING

 

If NOT factory installed, a main switch or other means for 
disconnection, having a contact separation in all poles provided full 
disconnection under overvoltage category III condition, MUST be 
installed in the fixed wiring.

 

WARNING

 

• 

ONLY use copper wires.

 

• 

Make sure the field wiring complies with the applicable 
legislation.

 

• 

All field wiring MUST be performed in accordance with the wiring 
diagram supplied with the product.

 

• 

NEVER squeeze bundled cables and make sure they do NOT come 
in contact with the piping and sharp edges. Make sure no 
external pressure is applied to the terminal connections.

 

• 

 Make sure to install earth wiring. Do NOT earth the unit to a 
utility pipe, surge absorber, or telephone earth. Incomplete earth 
may cause electrical shock.

 

• 

Make sure to use a dedicated power circuit. NEVER use a power 
supply shared by another appliance.

 

• 

Make sure to install the required fuses or circuit breakers.

 

• 

Make sure to install an earth leakage protector. Failure to do so 
may cause electric shock or fire.

 

• 

When installing the earth leakage protector, make sure it is 
compatible with the inverter (resistant to high frequency 
electrical noise) to avoid unnecessary opening of the earth 
leakage protector.

 

NOTICE

 

Precautions when laying power wiring:

 

• 

Do NOT connect wiring of different thicknesses to the power 
terminal block (Slack in the power wiring may cause abnormal 
heat.

 

• 

When connecting wiring which is the same thickness, do as 
shown in the figure above.

 

• 

For wiring, use the designated power wire and connect firmly, 
then secure to prevent outside pressure being exerted on the 
terminal board.

 

• 

Use an appropriate screwdriver for tightening the terminal 
screws. A screwdriver with a small head will damage the head 
and make proper tightening impossible.

 

• 

Over

-

tightening the terminal screws may break them.

 

Содержание UK.PPC150SL/R32























Отзывы: