Daikin SUT10D80L21-10-F Скачать руководство пользователя страница 51

Страница: 51 / 61

PIM-00004

△

[Operation Manual]

51/61

DAIKIN INDUSTRIES, LTD.

Return filter element replacement procedure

When the detector indicates clogging of the filter (the indicator ring floats up, and the green area of the

indicator column is completely hidden), replace the filter element according to the following procedure:

Loosen the hexagon socket head bolts [1] that fasten the cover [3], and pull up the cover. Then, the

element [5] can be removed.

Pull out the split pin [10] from the element, loosen the element tightening nut [9], and remove the parts [6]

to [8].

Replace the element with a new one, and re-mount it by following the above procedure in reverse.

Tighten the hexagon socket head bolts [1] securely in the diagonal order.

[1] Hexagon socket head bolt

[2] Plain washer

[9] Element tightening nut

[3] Cover

[4] Packing

[5] Element

[8] Spring washer

[11] O-ring

[10] Split pin

[7] Plain washer

[6] Packing

Содержание SUT10D80L21-10-F






























































Результаты поиска

Содержание SUT10D80L21-10-F

Отзывы:

Похожие инструкции для SUT10D80L21-10-F

Бренды по названию

Популярные бренды

Daikin SUT10D80L21-10-F, Руководство по эксплуатации

Результаты поиска

Содержание SUT10D80L21-10-F

Отзывы:

Похожие инструкции для SUT10D80L21-10-F

Бренды по названию

Популярные бренды