Daikin Super Multi NX FLKS25BAVMB Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 144

Daikin Super Multi NX FLKS25BAVMB Скачать руководство пользователя страница 132

Silicone Grease on Power Transistor / Diode Bridge

SiBE05-722EE

122

Trial Operation and Field Settings

4. Silicone Grease on Power Transistor / Diode

Bridge

Outline

Apply the specified silicone grease to the heat radiation part of a power transistor / diode bridge
when you replace an outdoor unit PCB. The silicone grease encourages the heat radiation of a
power transistor / diode bridge.

Detail

1. Wipe off the old silicone grease completely.
2. Apply the silicone grease evenly. See the illustrations below for examples of application.
3. Tighten the screws of the power transistor / diode bridge.
4. Make sure that the heat radiation parts are firmly contacted to the radiation fin.

Note: Smoke emission may be caused by bad heat radiation when the silicone grease is not

appropriately applied.

OK: Evenly applied

NG: Not evenly applied

NG: Foreign matter is stuck.

(R22541)

Power transistor
(or diode bridge)

Silicone grease

Radiation
fin

PCB

(R21866)

Foreign matter

(R21867)

«
...
130
131
132
133
134
...
»

Содержание Super Multi NX FLKS25BAVMB

















































































































































Отзывы:

Нет отзывов