Daikin Super Multi NX FLKS25BAVMB Скачать руководство пользователя страница 109

Страница: 109 / 144

SiBE05-722EE

Troubleshooting

Service Diagnosis

Troubleshooting

RK(X)S25/35G2V1B, RK(X)S25/35G2V1B9, RXS25/35J2V1B, RXS25K3V1B, RXS35K2V1B,
RXS25/35L2V1B, RXS25/35L3V1B

Check No.17

Refer to P.109

Check No.19

Refer to P.110

Note:

Refer to Silicone Grease on Power Transistor / Diode Bridge on page 122 for details.

Caution

Turn off the power. Then, turn on
the power to restart the system.

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

(R22540)

YES

Check the radiation fin
temperature.

YES

Above

˚C?

Check No. 19

Check the outdoor fan.

Error displayed again?

Has the PCB been

replaced?

Check if silicone grease is
applied properly on the
radiation fin. If not, apply
the silicone grease.

Replace the outdoor unit
PCB (main PCB).

Replace the outdoor fan
motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB (main PCB).

YES

Radiation fin dirty?

Clean up the radiation fin.

Check the installation
condition.
Go to

Check No. 17

(°C)

RK(X)S25/35G2V1B

RK(X)S25/35G2V1B9
RXS25/35J2V1B
RXS25K3V1B
RXS35K2V1B
RXS25/35L2V1B
RXS25/35L3V1B

Содержание Super Multi NX FLKS25BAVMB

















































































































































Результаты поиска

Содержание Super Multi NX FLKS25BAVMB

Отзывы:

Daikin Super Multi NX FLKS25BAVMB, Руководство по обслуживанию, Страница: 109 / 144

Результаты поиска

Содержание Super Multi NX FLKS25BAVMB

Отзывы: