Daikin RXP50N5V1B Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 72

Daikin RXP50N5V1B Скачать руководство пользователя страница 19

3

|

Specific installer safety instructions

Installer reference guide

19

RXF50~71D5V1B
R32 split series
4P519439-18T – 2022.06

DANGER: RISK OF BURNING/SCALDING

WARNING

▪

Before carrying out any maintenance or repair activity, ALWAYS switch off the
circuit breaker on the supply panel, remove the fuses or open the protection
devices of the unit.

▪

Do NOT touch live parts for 10 minutes after the power supply is turned off
because of high voltage risk.

▪

Please note that some sections of the electric component box are hot.

▪

Make sure you do NOT touch a conductive section.

▪

Do NOT rinse the unit. This may cause electric shocks or fire.

DANGER: RISK OF ELECTROCUTION

▪

Use this compressor on a grounded system only.

▪

Turn the power off before servicing the compressor.

▪

Reattach the switch box cover and service lid after servicing.

CAUTION

ALWAYS wear safety glasses and protective gloves.

DANGER: RISK OF EXPLOSION

▪

Use a pipe cutter to remove the compressor.

▪

Do NOT use the brazing torch.

▪

Use approved refrigerants and lubricants only.

DANGER: RISK OF BURNING/SCALDING

Do NOT touch the compressor with bare hands.

Troubleshooting (see

"14 Troubleshooting"

)

DANGER: RISK OF ELECTROCUTION

DANGER: RISK OF BURNING/SCALDING

WARNING

▪

When carrying out an inspection on the switch box of the unit, ALWAYS make
sure that the unit is disconnected from the mains. Turn off the respective circuit
breaker.

▪

When a safety device was activated, stop the unit and find out why the safety
device was activated before resetting it. NEVER shunt safety devices or change
their values to a value other than the factory default setting. If you are unable to
find the cause of the problem, call your dealer.

«
...
17
18
19
20
21
...
»

Содержание RXP50N5V1B









































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды