background image

35

3P477778-7G

English

15 .2 .3 .  Auxiliary heat control

To improve efficiency the aux heat can be lockout based on outdoor 

temperature.

Item

Description

Min

Max

Increments

AUX Heater 

 

Allowable Temp

Below this tempera-

ture, AUX heater can 

be energized based 
on the indoor tempera-
ture condition.

0F

65F  

(35F 

default)

5F

AUX Heater 

Allowable temp 
Release  
differential

When the outdoor 
temp recovered by 

this temp, AUX heater 

cannot be allowed.

5F, 10F (default), 15F

[2-97]=  Aux heater max allowable temp

AUX Heater is allowed to energize when the ambient temp is 
smaller than the AUX Heater Max Allowable Temp.

AUX Heater Max 

Allowable Temp

Fahrenheit

Celsius

0

0

− 17.7

1

5

− 15

2

10

− 12.2

3

15

− 9.4

4

20

− 6.6

5

25

− 3.8

6

30

− 1.1

7

35 (default)

1.6 (default)

8

40

4.4

9

45

7.2

10

50

10

11

55

12.7

12

60

15.5

13

65

18.3

14

AUX Heater always NOT allowed

15

AUX Heater always allowed

[2-98]=   Aux heater max allowable temp release differential

AUX Heater is not allowed to energize when the outdoor 

ambient temp is recovered by differential (below) above the 

AUX Heater Max Allowable Temp.

AUX Heater Max Allowable 

temp Release differential

Fahrenheit

Celsius

0

5

2.8°C

1

10  

(default)

5.6°C  

(default)

2

15

8.3°C

15 .2 .4 .  Heat pump lockout

• 

New control logic to provide more application options for cold 
climates.

• 

Outside temperature can now be measured directly from the out-
door unit coil sensor.

• 

VRV IV HR, VRV-S and VRV Cold Climate can also be programed to 
automatically switch to emergency heat is there is a system fault.

Item

Description

Min

Max Increments

Heat Pump 
Lockout Temp

Below this tempera-
ture, heat pump is 
locked out.

− 15F 

 

(default)

50F

5F

Heat Pump 
Lockout Release 
differential

When the outdoor 
temp is recovered by 
this temp, heat pump 
is resumed.

5F, 10F (default), 15F

[2-16]=   Aux heater setting (Type 

I

)

Value [2-16]

Aux heater

0

OFF

1

ON

[2-37]=   Aux heater setting (Type 

II

)

Value [2-37]

Controlling mode

1

Mode 1

2

Mode 2

3

Mode 3

4

Mode 4

5

Mode 5

6

Mode 6

01_EN_3P477778-7G.indb   35

1/15/2019   10:58:30

Содержание REYQ120XATJU


















































Отзывы: