background image

33

3P477778-7G

English

[2-26]=   Low noise operation start time

Change [2-26]=1, 2 or 3 in function of required timing.

Default value=2.

Value 
[2-26]

Start time automatic low noise 

operation (approximately)

1

8:00 p.m.

2

10:00 p.m. (default)

3

12:00 a.m.

This setting is used in conjunction with setting [2-22].

[2-27]=   Low noise operation stop time

Default value=3.

Value 
[2-27]

Start time automatic low noise 

operation (approximately)

1

6:00 a.m.

2

7:00 a.m.

3

8:00 a.m. (default)

This setting is used in conjunction with setting [2-22]. 

[2-30]=   Power consumption limitation level (step 1) via the external 

control adaptor (DTA104A61/62)

If the system needs to run under power consumption limita-

tion conditions when an external signal is sent to the unit, 
this setting defines the level power consumption limitation 

that will be applied for step 1. The level is according to the 
table.
Default value=3.

Change [2-30]=1, 2, 3, 4, 5, 6, 7 or 8 in function of required 

limitation.

Value 
[2-30]

Power consumption limitation 

(approximately)

1

60%

2

65%

3

70% (default)

4

75%

5

80%

6

85%

7

90%

8

95%

[2-31]=   Power consumption limitation level (step 2) via the external 

control adaptor (DTA104A61/62)

If the system needs to run under power consumption limita-

tion conditions when an external signal is sent to the unit, 
this setting defines the level power consumption limitation 

that will be applied for step 2. The level is according to the 
table.
Default value=1.

Change [2-31]=1, 2 or 3 in function of required limitation.

Value 
[2-31]

Power consumption limitation 

(approximately)

1

40% (default)

2

50%

3

55%

 [2-32]=  Forced, all time, power consumption limitation operation 

(no external control adaptor is required to perform power 

consumption limitation)

If the system always needs to run under power consump-

tion limitation conditions, this setting activates and defines 

the level power consumption limitation that will be applied 
continuously. The level is according to the table.
Default value=0 (OFF).

Value 
[2-32]

Restriction reference

0

Function not active (default)

1

Follows [2-30] setting

2

Follows [2-31] setting

Change [2-32]=0, 1 or 2 in function of required limitation.

[2-34]=  Indoor unit fan tap setting

Indoor units fan speed limitation related to connection ca-
pacity and outdoor air temperature for energy saving.

Default value=0.

Value 
[2-34]

Indoor unit fan tap setting

0

Fan speed is limited to L tap when indoor units 

capacity ≥130%.

1

In heating mode, fan speed is limited to L tap 

when indoor units capacity ≥130%.

2

Fan speed follows the setting of remote controllers 
(not limited by indoor units connection capacity).

See the service manual for other indoor unit fan tap settings.

01_EN_3P477778-7G.indb   33

1/15/2019   10:58:30

Содержание REYQ120XATJU


















































Отзывы: