Daikin REMQ8P9Y1B, Руководство по установке

Страница: 18 / 36

Installation manual
13
R REMQ10~16P8 + REMHQ12P8Y1B
VRVIII System air conditioner
4PW48463-1A
Y1S~Y7S............. Solenoid valve (RMTG, 4 way valve–PPE, 4 way
valve–H/E gas, RMTL, hot gas, EV bypass,
RMTO)
Z1C~Z10C........... Noise filter (ferrite core)
Z1F...................... Noise filter (with surge absorber)
L1,L2,L3 .............. Live
N.......................... Neutral
............ Field wiring
............... Terminal strip
....................... Connector
...................... Terminal
....................... Protective earth (screw)
BLK ..................... Black
BLU ..................... Blue
BRN..................... Brown
GRN .................... Green
GRY..................... Grey
ORG .................... Orange
PNK..................... Pink
RED..................... Red
WHT .................... White
YLW..................... Yellow
8.2. Optional parts connector
X7A ..................... Operation output (A5P)
X9A ..................... Power supply (adapter) (A5P)
8.3. Power circuit and cable requirements
A power circuit (see table below) must be provided for connection of
the unit. This circuit must be protected with the required safety
devices, i.e. a main switch, a slow blow fuse on each phase and an
earth leakage breaker.
When using residual current operated circuit breakers, be sure to use
a high-speed type 300 mA rated residual operating current.
Point for attention regarding quality of the public electric power
supply
This equipment complies with respectively:
■
EN/IEC 61000-3-11
(1)
provided that the system impedance Z
sys
is less than or equal to Z
max
and
■
EN/IEC 61000-3-12
(2)
provided that the short-circuit power S
sc
is greater than or equal to the minimum S
sc
value
at the interface point between the user's supply and the public
system. It is the responsibility of the installer or user of the equipment
to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with
respectively:
■
Z
sys
less than or equal to Z
max
and
■
S
sc
greater than or equal to the minimum S
sc
value.
NOTE
■
This wiring diagram only applies to the outdoor
unit.
■
When using the option adaptor, refer to the
installation manual.
■
Refer to the installation manual, for connection
wiring to indoor-outdoor transmission F1-F2,
outdoor-outdoor transmission F1-F2,
outdoor-multi transmission Q1-Q2 and on how to
use BS1~BS5 and DS1, DS2 switch.
■
Do not operate the unit by short-circuiting
protection device S1PH~S3PH.
NOTE
■
Use copper conductors only.
■
For connection wiring to the central remote
controller, refer to the installation manual of the
central remote controller.
■
Use insulated wire for the power cord.
Phase and
frequency Voltage
Minimum
circuit
ampere
Recommended
fuses
Transmission line
section
REYQ18 3N~ 50 Hz 400 V 40.1 A 50 A 0.75~1.25 mm
2
REYQ20 3N~ 50 Hz 400 V 41.2 A 50 A 0.75~1.25 mm
2
REYQ22 3N~ 50 Hz 400 V 44.3 A 50 A 0.75~1.25 mm
2
REYQ24 3N~ 50 Hz 400 V 45.4 A 50 A 0.75~1.25 mm
2
REYQ26 3N~ 50 Hz 400 V 53.1 A 63 A 0.75~1.25 mm
2
REYQ28 3N~ 50 Hz 400 V 54.2 A 63 A 0.75~1.25 mm
2
REYQ30 3N~ 50 Hz 400 V 63.0 A 80 A 0.75~1.25 mm
2
REYQ32 3N~ 50 Hz 400 V 63.0 A 80 A 0.75~1.25 mm
2
REYQ34 3N~ 50 Hz 400 V 71.6 A 80 A 0.75~1.25 mm
2
REYQ36 3N~ 50 Hz 400 V 72.7 A 80 A 0.75~1.25 mm
2
REYQ38 3N~ 50 Hz 400 V 75.8 A 80 A 0.75~1.25 mm
2
REYQ40 3N~ 50 Hz 400 V 76.9 A 80 A 0.75~1.25 mm
2
REYQ42 3N~ 50 Hz 400 V 84.6 A 100 A 0.75~1.25 mm
2
REYQ44 3N~ 50 Hz 400 V 85.7 A 100 A 0.75~1.25 mm
2
REYQ46 3N~ 50 Hz 400 V 94.5 A 100 A 0.75~1.25 mm
2
REYQ48 3N~ 50 Hz 400 V 94.5 A 100 A 0.75~1.25 mm
2
Phase and
frequency Voltage
Minimum
circuit
ampere
Recommended
fuses
Transmission line
section
REYHQ16 3N~ 50 Hz 400 V 37 A 50 A 0.75~1.25 mm
2
REYHQ20 3N~ 50 Hz 400 V 50 A 63 A 0.75~1.25 mm
2
REYHQ22 3N~ 50 Hz 400 V 53.1 A 63 A 0.75~1.25 mm
2
REYHQ24 3N~ 50 Hz 400 V 63 A 80 A 0.75~1.25 mm
2
(1) European/International Technical Standard setting the limits for voltage changes,
voltage fluctuations and flicker in public low-voltage supply systems for equipment
with rated current
≤
75 A.
(2) European/International Technical Standard setting the limits for harmonic currents
produced by equipment connected to public low-voltage systems with input
current >16 A and
≤
75 A per phase.