manualshive.com logo in svg

Daikin FTXN09KEVJU, Руководство по обслуживанию

Поделиться
Скачать
Daikin FTXN09KEVJU Скачать руководство пользователя страница 47

SiUS041111

Control Specification

Function and Control

39

3.4

Discharge Pipe Temperature Control

Outline

The discharge pipe temperature is used as the internal temperature of the compressor. If the 
discharge pipe temperature rises above a certain level, the upper limit of frequency is set to keep 
this temperature from going up further.

Detail

Zone

Control

Stop zone

When the temperature reaches the stop zone, the compressor stops.

Dropping zone

The upper limit of frequency decreases.

Keep zone

The upper limit of frequency is kept.

Up zone

The upper limit of frequency increases.

Reset zone

The upper limit of frequency is canceled.

09/12 class

15/18/24 class

A

110°C (230°F)

118°C (244.4°F)

B

105°C (221°F)

108°C (226.4°F)

C

101°C (213.8°F)

103°C (217.4°F)

D

99°C (210.2°F)

97°C (206.6°F)

E

97°C (206.6°F)

85°C (185°F)

(R14722)

Discharge pipe 

temperature

Stop zone

Dropping zone

Keep zone

Up zone

Reset zone

E

A

B

C

D

Содержание FTXN09KEVJU





















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды