14
Ŷ
English
Refrigerant Piping Work
4GHGTCNUQVQVJGKPUVCNNCVKQPOCPWCNHQTVJGQWVFQQTWPKV
WARNING
r &QPQVCRRN[OKPGTCNQKNQPƃCTGFRCTV
r
Prevent mineral oil from getting into the system as this would reduce the service life of the units.
r
Never use piping which has been used for previous installations. Only use parts which are delivered with the unit.
r
Never install a dryer to this R410A unit in order to guarantee its service life.
r
The drying material may dissolve and damage the system.
r +PEQORNGVGƃCTKPIOC[TGUWNVKPTGHTKIGTCPVICUNGCMCIG
'ZGEWVGVJGTOCNKPUWNCVKQPYQTMEQORNGVGN[QPDQVJUKFGUQHVJGICUCPFVJGNKSWKFRKRKPI1VJGTYKUGCYCVGTNGCMCIGECP
TGUWNVUQOGVKOGU
$GUWTGVQWUGKPUWNCVKQPFGUKIPGFHQTWUGYKVJ*8#%U[UVGOU
#NUQKPECUGUYJGTGVJGVGORGTCVWTGCPFJWOKFKV[QHVJGTGHTKIGTCPVRKRKPIUGEVKQPUOKIJVGZEGGF(%QT4*
TGKPHQTEGVJGTGHTKIGTCPVKPUWNCVKQPKPEJOOQTVJKEMGT%QPFGPUCVKQPOC[HQTOQPVJGUWTHCEGQHVJGKPUWNCVKPI
OCVGTKCN
$GHQTGTGHTKIGTCPVRKRKPIYQTMEJGEMYJKEJV[RGQHTGHTKIGTCPVKUWUGF2TQRGTQRGTCVKQPKUPQVRQUUKDNGKHVJGV[RGUQH
TGHTKIGTCPVCTGPQVVJGUCOG
1.
Flaring the pipe end
1) Cut the pipe end with a pipe cutter.
2) Remove burrs with the cut surface facing downward
UQVJCVVJGƂNKPIUFQPQVGPVGTVJGRKRG
3)
2WVVJGƃCTGPWVQPVJGRKRG
4) Flare the pipe.
5)
%JGEMVJCVVJGƃCTKPIJCUDGGPFQPGEQTTGEVN[
A
A
Cut exactly at
right angles.
Remove burrs.
Flaring
Set exactly at the position shown below.
Die
0-0.020 inch
(0-0.5mm)
Clutch-type
Flare tool for
R410A
0.039-0.059 inch
(1.0-1.5mm)
Clutch-type
(Rigid-type)
0.059-0.079 inch
(1.5-2.0mm)
Wing-nut type
(Imperial-type)
%QPXGPVKQPCNƃCTGVQQN
6JGƃCTG UKPPGT
surface must be
ƃCYHTGG
The pipe end must
DGGXGPN[ƃCTGFKPC
perfect circle.
Make sure that the
ƃCTGPWVKUƂVVGF
Check
2.
Refrigerant piping
CAUTION
r
Use the flare nut fixed to the main unit. (This is to prevent the flare nut from cracking as a result of deterioration over time.)
r
To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R410A.)
r
Use a torque wrench when tightening the flare nuts to prevent damage to the flare nuts and gas leakage.
r #NKIPVJGEGPVGTUQHDQVJƃCTGUCPFVKIJVGPVJGƃCTGPWVUQTVWTPUD[JCPFVJGPVKIJVGPVJGOHWNN[YKVJCURCPPGTCPF
a torque wrench.
Do not apply refrigeration
oil to the outer surface.
Flare nut
Apply refrigeration
oil only to the inner
UWTHCEGQHVJGƃCTG
Do not apply refrigeration oil to
VJGƃCTGPWVVQCXQKFVKIJVGPKPI
YKVJGZEGUUKXGVQTSWG
Apply oil
6QTSWGYTGPEJ
Piping union
Flare nut
Spanner
Tighten
Piping size
Flare nut tightening torque
Gas side
O.D. 3/8 inch (9.5mm)
s+DHrHV0rO
O.D. 1/2 inch (12.7mm)
s+DHrHV0rO
Liquid side
O.D. 1/4 inch (6.4mm)
s+DHrHV0rO
English
Содержание FFQ09Q2VJU
Страница 62: ...21 ŶEspañol MEMO ...
Страница 63: ...22 ŶEspañol Español ...
Страница 64: ...Two dimensional bar code is a manufacturing code 3P436085 1 M15B215 1607 HT ...