Daikin ETVZ16S23EA9W, Руководство по установке

Страница: 14 / 40

6 Electrical installation
Installation manual
14
ET9W
Daikin Altherma 3 H HT F
4P644730-1 – 2021.02
Backup
heater type
Backup
heater
capacity
Power
supply
Maximum
running
current
Z
max
*9W 3 kW 3N~ 400 V 4 A —
6 kW 3N~ 400 V 9 A —
9 kW 3N~ 400 V 13 A —
(a)
6V
(b)
Electrical equipment complying with EN/IEC 61000-3-12
(European/International Technical Standard setting the limits for
harmonic currents produced by equipment connected to public
low-voltage systems with input current >16 A and ≤75 A per
phase).
(c)
This equipment complies with EN/IEC 61000‑3‑11 (European/
International Technical Standard setting the limits for voltage
changes, voltage fluctuations and flicker in public low-voltage
supply systems for equipment with rated current ≤75 A) provided
that the system impedance Z
sys
is less than or equal to Z
max
at the
interface point between the user's supply and the public system. It
is the responsibility of the installer or user of the equipment to
ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with
a system impedance Z
sys
less than or equal to Z
max
.
(d)
6T1
Connect the backup heater power supply as follows:
X6M
F1B
Q1DI
a
b
a Factory-mounted cable connected to the contactor of the
backup heater, inside the switch box (K5M)
b Field wiring (see table below)
Model (power
supply)
Connections to backup heater power
supply
*6V (6V: 1N~ 230 V)
1N~, 50 Hz
230 V AC
SWB
4
3 6
5 2
1
K5M
14
13
Q1DI
1
2
3
4
5
6
7
8
F1B
I I I I
N L
X6M
BRN GRY BLU1
BLU2
Model (power
supply)
Connections to backup heater power
supply
*6V (6T1: 3~ 230 V)
SWB
3~, 50 Hz
230 V AC
4
3 6
5 2
1
K5M
14
13
1
2
3
4
5
6
7
8
F1B
I I I I
Q1DI
L1 L2 L3
X6M
BRN GRY BLU1
BLU2
*9W (3N~ 400 V)
3N~, 50 Hz
400 V AC
SWB
Q1DI
L1 L2 L3 N
1
2
3
4
5
6
7
8
F1B
I I I I
X6M
2
1
K5M
4
3 6
5 14
13
BRN GRY
BLK
BLU
F1B Overcurrent fuse (field supply). Recommended fuse:
4‑pole; 20 A; curve 400 V; tripping class C.
K5M Safety contactor (in the lower switch box)
Q1DI Earth leakage circuit breaker (field supply)
SWB Switch box
X6M Terminal (field supply)
NOTICE
Do NOT cut or remove the backup heater power supply
cable.
6.3.3 To connect the shut-off valve
INFORMATION
Shut-off valve usage example. In case of one LWT zone,
and a combination of underfloor heating and heat pump
convectors, install a shut-off valve before the underfloor
heating to prevent condensation on the floor during cooling
operation. For more information, see the installer reference
guide.
Wires: 2×0.75 mm²
Maximum running current: 100 mA
230 V AC supplied by PCB
[2.D] Shut off valve
1 Open the following (see "4.2.1 To open the indoor unit" [
4
6]):