background image

11

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each 
appliance connected to the venting system being placed 
into operation could result in carbon monoxide poisoning 
or death.

The following steps shall be followed with each appliance 
connected to the venting system placed in operation, 
while any other appliances connected to the venting 
system are not in operation:

1.  Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and 

horizontal pitch, as required by the National Fuel Gas 
Code, ANSI Z223.1 or the Natural Gas and Propane 
Installation Code, CSA B149.1-15 and these 
instructions. Determine that there is no blockage or 
restriction, leakage, corrosion and other deficiencies 
which could cause an unsafe condition.

3. As far as practical, close all building doors and 

windows and all doors between the space in which 
the appliance(s) connected to the venting system are 
located and other spaces of the building.

4.  Close fireplace dampers.

5. Turn on clothes dryers and any appliance not 

connected to the venting system. Turn on any 
exhaust fans, such as range hoods and bathroom 
exhausts, so they shall operate at maximum speed. 
Do not operate a summer exhaust fan.

6.  Follow the lighting instructions. Place the appliance 

being inspected in operation. Adjust thermostat so 
appliance shall operate continuously.

7.  Test for spillage from draft hood appliances at the 

draft hood relief opening after 5 minutes of main 
burner operation. Use the flame of a match or 
candle.

8.  If improper venting is observed during any of the 

above tests, the venting system must be corrected in 
accordance with the National Fuel Gas Code ANSI 
Z223.1/NFPA 54 and/or National Gas and Propane 
Installation Code CSA B149.1-15.

9.  After it has been determined that each appliance 

connected to the venting system properly vents 
when tested as outlined above, return doors, 
windows, exhaust fans, fireplace dampers and any 
other gas burning appliance to their previous 
conditions of use.

WARNING

RISQUE D'INTOXICATION AU MONOXYDE DE CARBONE

Si les étapes décrites ci-dessous ne sont pas suivies pour 
chacun des appareils raccordés au système de ventilation 
au moment de sa mise en marche, cela peut entraîner une 
intoxication au monoxyde de carbone ou la mort. Les 
étapes suivantes doivent être suivies pour chacun des 
appareils raccordés au système de ventilation au moment 
de sa mise en marche, alors que tous les autres appareils 
raccordés au système de ventilation ne sont pas en 
marche :
1) Sceller toutes les ouvertures inutilisées du système de 
ventilation.
2) Inspecter le système de ventilation afin de vérifier si la 
taille et l'inclinaison par rapport à l'horizontale sont 
conformes aux exigences du National Fuel Gas Code, ANSI 
Z223.1/NFPA 54 ou du Code d'installation du gaz naturel 
et du propane, CSA B149.1 et à ces instructions. Vérifier 
qu'il n'y a pas d'obstruction ou de restriction, de fuite, de 
corrosion et d'autres problèmes qui pourraient entraîner 
une situation dangereuse.
3) Si possible, fermer toutes les portes et fenêtres du 
bâtiment ainsi que toutes les portes séparant l'endroit où 
se trouvent les appareils raccordés au système de 
ventilation et les autres zones du bâtiment.
4) Fermer le registre des foyers.
5) Mettre les sécheuses en marche ainsi que tous les 
autres appareils qui ne sont pas raccordés au système de 
ventilation. Mettre en marche tous les ventilateurs de 
tirage, comme celui des hottes de cuisine et des salles de 
bains, et les régler à la puissance maximale. Ne pas mettre 
en marche les ventilateurs d'été.
6) Suivre les instructions d'allumage. Mettre en marche 
l'appareil soumis à l'inspection. Régler le thermostat de 
manière à ce que l'appareil fonctionne en continu.
7) Vérifier la présence de fuite au niveau de l'ouverture du 
coupe-tirage des appareils qui en sont dotés après 5 
minutes de fonctionnement du brûleur principal. Utiliser 
la flamme d'une allumette ou d'une bougie.
8) Si un problème de ventilation est observé pendant l'un 
des essais décrits ci-dessus, des correctifs doivent être 
apportés au système de ventilation conformément au 
National Fuel Gas Code, ANSI Z223.1/NFPA 54 et (ou) au 
Code d'installation du gaz naturel et du propane, CSA 
B149.1.
9) Une fois qu'il a été déterminé que chaque appareil 
raccordé au système de ventilation fonctionne 
correctement au moyen des essais décrits ci-dessus, les 
portes, les fenêtres, les ventilateurs, les registres de foyer 
et tous les autres appareils de combustion alimentés au 
gaz doivent être remis dans leur état initial.  

AVERTISSEMENT

If this furnace is to be installed in the same space with other
gas appliances, such as a water heater, ensure there is an
adequate supply of combustion and ventilation air for all appli-
ances.  Refer to the latest edition of the National Fuel Gas
Code NFPA 54/ANSI Z223.1 or CAN/CSA B149 Installation
Codes or applicable provisions of the local building codes for
determining the combustion air requirements for the appliances.

Содержание DM80VC





















































Отзывы: