Daikin ARKH20CVMB7 Скачать руководство пользователя страница 90

Страница: 90 / 248

SiENBE04-512A

Instruction

System Configuration

2.8

HOME LEAVE Operation

Before using HOME LEAVE operation

HOME LEAVE operation is a function which allows you to record your
preferred temperature and air flow rate settings.

To start HOME LEAVE operation

1. Press “HOME LEAVE button”.

•

“

” is displayed on the LCD.

•

The HOME LEAVE lamp lights up.

To cancel HOME LEAVE operation

2. Press “HOME LEAVE button” again.

•

The HOME LEAVE lamp goes off.

•

“

” disappears from the LCD.

To set the temperature and air flow rate for HOME LEAVE operation
When using HOME LEAVE operation for the first time, please set the temperature and air flow rate for HOME LEAVE
operation. Record your preferred temperature and air flow rate.

1. Press “HOME LEAVE button”. Make sure “

” is displayed in the remote control display.

2. Adjust the set temperature with “

” or “

” as you like.

3. Adjust the air flow rate with “FAN” setting button as you like.

Home leave operation will run with these settings the next time you use the unit. To change the recorded information,
repeat steps 1 – 3.

OFF

Initial setting

Selectable range

temperature

Air flow rate

temperature

Air flow rate

Cooling

25°

AUTO

18-32°C

5 step, AUTO and SILENT

Heating

25°

AUTO

10-30°C

5 step, AUTO and SILENT

SiENBE04-512A.book Page 81 Friday, October 5, 2007 1:49 PM

Содержание ARKH20CVMB7

























































































































































































































































Результаты поиска

Содержание ARKH20CVMB7

Отзывы:

Похожие инструкции для ARKH20CVMB7

Бренды по названию

Популярные бренды

Daikin ARKH20CVMB7, Руководство по обслуживанию

Результаты поиска

Содержание ARKH20CVMB7

Отзывы:

Похожие инструкции для ARKH20CVMB7

Бренды по названию

Популярные бренды