background image

9 Installation

Installer reference guide

33

EJHA EHY32AA
Daikin Altherma Hybrid hydrosplit heat pump
4P531180-1 – 2018.06

NOTICE

Cold climates.

 If the unit is installed in a cold climate:

▪ Take  adequate  measures  so  that  the  evacuated

condensate CANNOT freeze.

▪ Do  NOT  use  the  drain  plug  and  drain  hose  with  the

outdoor  unit. 

Possible  consequence: 

Drain  water

might freeze, decreasing the heating capacity.

NOTICE

Provide  at  least  300  mm  of  free  space  below  the  unit.
Additionally,  make  sure  the  unit  is  positioned  at  least
100 mm above the expected level of snow.

Except in cold climates, use the drain plug and a hose for drainage.

b

c

d

a

a

Drain hole

b

Bottom frame

c

Drain plug (delivered as accessory)

d

Hose (field supply)

9.3.6

To prevent the outdoor unit from falling
over

In  case  the  unit  is  installed  in  places  where  strong  wind  can  tilt  the
unit, take following measure:

1

Prepare  2  cables  as  indicated  in  the  following  illustration  (field
supply).

2

Place the 2 cables over the outdoor unit.

3

Insert  a  rubber  sheet  between  the  cables  and  the  outdoor  unit
to prevent the cables from scratching the paint (field supply).

4

Attach the ends of the cables and tighten them.

9.4

Mounting the gas boiler

9.4.1

To install the gas boiler

1

Lift the unit from the package.

33~36kg

2

The bracket to mount the boiler on the heat pump module is an
accessory of the gasboiler. Fix the wall bracket to the wall with
2 M8 bolts.

3

Lift the boiler. One person lifts the gas boiler on the left side (left
hand  on  the  top  and  right  hand  on  the  bottom)  and  another
person  lifts  the  gas  boiler  on  the  right  side  (left  hand  on  the
bottom and right hand on the top).

4

Tilt  the  top  of  the  unit  at  the  position  of  the  wall  bracket  and
slide the boiler downwards to fix the boiler bracket onto the wall
bracket.

5

Make sure the gas boiler is fixed properly to the wall.

Содержание Altherma EHY2KOMB28AA

















































































































Отзывы: