Daihatsu TERIOS J100 Скачать руководство пользователя

Страница: 43 / 96

INSPECTION

1. Ensure that the seat belt will not be locked until the seat

belt retractor is tilted more than 15 degrees in all direc-
tions.
Also, ensure that the locked state is retained when the re-
tractor is tilted 45 degrees or more.

2. Ensure that the seat belt will be locked when the seat belt

is pulled quickly.

3. Ensure that no scratch, wear or any other damage exists

on the seat belts.
If any damage is found, replace the seat belt with a new
one.

CAUTION:

Never attempt to disassemble the retractor.

After the anchor bolts have been tightened, make sure
that each anchor can move in a circumferential direc-
tion of the bolt.

Ensure that the belt in the installed state can be pulled
out smoothly and also it can be retracted smoothly in
position.

INSTALLATION

1. Install the rear seat inner belt assembly and center seat belts with the attaching bolt. Then, tighten the

attaching bolt to the specified tightening torque.

Tightening Torque:

40.5

12.5 N·m (4.1

1.3 kgf-m)

2. Install the rear seat belt retractor with the attaching bolt and tighten it to the specified tightening torque.

Tightening Torque:

40.5

12.5 N·m (4.1

1.3 kgf-m)

3. Install the rear seat belt upper anchor with the attaching bolt and tighten it to the specified tightening

torque.

Tightening Torque:

40.5

12.5 N·m (4.1

1.3 kgf-m)

4. Close the seat belt anchor bolt cover of the rear seat belt upper anchor.
5. Install the deck side trim. (Refer to the trim & garnish section for the installation procedure.)
6. Install the rear door scuff plate assembly. (Refer to the trim & garnish section for the installation proce-

dure.)

7. Install the rear seat belt end anchor with the attaching bolts and tighten them to the specified tightening

torque.

Tightening Torque:

40.5

12.5 N·m (4.1

1.3 kgf-m)

8. Install the deck board assembly. (Refer to the trim & garnish section for the installation procedure.)
9. Install the lower back trim. (Refer to the trim & garnish section for the installation procedure.)

10. Install the rear seat. (Refer to the rear seat section for the installation procedure.)

BO–43

JBO00108-00091

JBO00109-00000

Содержание TERIOS J100

































































































Результаты поиска

Содержание TERIOS J100

Отзывы:

Похожие инструкции для TERIOS J100

Бренды по названию

Популярные бренды

Daihatsu TERIOS J100, Руководство по обслуживанию

Результаты поиска

Содержание TERIOS J100

Отзывы:

Похожие инструкции для TERIOS J100

Бренды по названию

Популярные бренды