Daewoo Solar 300LC-V Скачать руководство пользователя страница 490 | Manualshive

Страница: 490 / 658

background image

S0709401K
Page 46

Main Control Valve (Kayaba)

14.

Remove spring (48) and poppet (49) from valve housing.

15.

Remove socket head bolt (101, four places, width across flats: 8 mm) from body (96, one places).

16.

Remove body (96) from valve housing. Remove sleeve (99), piston (97), spring (98), poppet
assembly (100), backup ring (103), and O-ring (104).

17.

Remove O-ring (36).

18.

Grip body (96) in vise. Remove plug (94), piston (95) and O-ring (102).

Disassembly of Antidrift Valve

Small parts in assembly is indicated to (parental number - son number).

1.

Remove socket head bolt assembly (76, four places per section, width across flats: 8 mm) and
antidrift valve assembly (67, two places).

2.

Remove O-ring (41, 42) from valve housing. Remove O-ring (40-4) from spacer assembly.

3.

Screw socket head bolt (78, M6*1) into spacer, and remove spacer assembly (40) from valve housing.

4.

Remove O-ring (40-2) and backup ring (40-3).

5.

Remove spring (39) and poppet (38) from valve housing.

6.

Disassembly of antidrift valve assembly

A.

Remove plug assembly (67-14, width across flats: 38 mm) and O-ring.

B.

Remove piston (67-4), spool (67-5), and spring (67-7).

C.

Remove plug (67-3, width across flats: 38 mm) and O-ring.

D.

Remove sleeve (67-6) and poppet (67-2) from body. Remove O-ring (67-9, 10) and backup ring
(67-11, 12) from outside diameter of sleeve.

E.

Pull spring seat (67-16) and spring (67-8) out of inside hole.

F.

Remove plug assembly (67-15) if necessary.

NOTE:

But do not remove steel ball (67-14) because it is pressed in body.

CAUTION!

Removing antidrift valve seat, when pressure is not fully released, or bucket is not lowered to
ground, is very dangerous. A part in the valve may spring out and drop the bucket at the same
time. Always lower bucket to ground and fully release pressure before disassembling.

CAUTION!

Removing inner parts of antidrift valve, when pressure is not fully released, or bucket is not
lowered to ground, is very dangerous. A part in the valve may spring out and drop the
bucket at the same time. Always lower bucket to ground and fully release pressure before
disassembling.

Slowly loosen plug assembly (67-14) and plug (67-3), check if there is a resistance by
remaining pressure and remove.

«
...
488
489
490
491
492
...
»

Содержание Solar 300LC-V



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar 300LC-V

Бренд: Wallenstein Страницы: 50

Бренд: Kubota Страницы: 115

Бренд: Meec tools Страницы: 53

Бренд: SUNWARD Страницы: 102

Бренд: Magni Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды