manualshive.com logo in svg

Daewoo Solar 300LC-V, Руководство пользователя

Даэву Солар 300LC-V - это мощный экскаватор, который поможет вам эффективно выполнять строительные работы. Скачайте бесплатное руководство по эксплуатации на manualshive.com и ознакомьтесь с основными функциями и возможностями этого устройства. Улучшите свою работу с помощью данного мануала!

Поделиться
Скачать
background image

S0702170K
Page 24

Hydraulic System Troubleshooting, Testing and

Adjustment

Pressure should stay consistently above 2.5 bar (36 psi). If pressure falls below the
recommended minimum level, forceful acceleration of the swing motor could lead to cavitation
of the circuit and stalling, slowed rotation, noise and possible damage.

2.

If main inlet and outlet pressures were off in the preceding tests in Step 1, adjust swing relief valve
pressure.

Following adjustment, repeat the operating pressure tests (with gauges connected to the inlet and
outlet test ports on top of the swing motor) and check pressures with the swing locks engaged and
released.

If pressure adjustment fails to restore adequate performance, proceed to the Troubleshooting –
Swing table.

3.

If pressure tests were at recommended levels through the main inlet and outlet ports, and through the
“SH” port of the swing brake, the causes of poor swing performance could include a faulty swing
motor, drive train overloading or gearbox defect, or a problem in the brake assembly or swing control
valve. Proceed to the troubleshooting information in the next procedure.

If pressure through the “SH” port was tested below the minimum 13 bar (190 psi) level, check the
shuttle valve in the rear compartment behind cabin. When pressure through the port is at the
recommended level, the brake release valve should disengage the swing brake, allowing the swing
motor to rotate the excavator. If pressure adjustment to the valve has been restored but the brake still
fails to release, the brake piston or friction plate may be frozen, requiring disassembly of the motor
and parts repair/replacement.

4.

If pressure tested at the motor makeup valve falls below recommended minimum level, and
consequent problems with cavitation, stalling and surging are observed, check the restriction valve. If
pressure adjustment to the valve has been restored but if problems with cavitation continues,
disassemble the upper swing motor housing and clean or replace assembly components as required.

NOTE:

If all tested pressures are at or above recommended levels, and there are no mechanical
problems in the drive train or in the motor/brake assembly, the problem will require further
hydraulic troubleshooting. It’s also possible that a defective joystick, an intermittent short in
an electrical control circuit or a problem in the e-EPOS circuit is causing diminished swing
performance. Pull out the e-EPOS indicator panel from underneath the operator’s seat
and perform the self-diagnosis test. If the display panel reads code “0.2,” it is reporting that
the swing priority proportional valve is not functioning, except in the minimum “fail-safe”
mode. Refer to the Electrical section of this book for more information.

Содержание Solar 300LC-V



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar 300LC-V

Maxon BMR-CS Installation Manual preview
BMR-CS
Бренд: Maxon Страницы: 103
Kato REDGZM HD514MR-7 Instruction Manual preview
REDGZM HD514MR-7
Бренд: Kato Страницы: 325
jcb JS70 Service Manual preview
JS70
Бренд: jcb Страницы: 385
Terex TW85 Operating Instructions Manual preview
TW85
Бренд: Terex Страницы: 125
Komatsu PC18MR-3 Operation & Maintenance Manual preview
PC18MR-3
Бренд: Komatsu Страницы: 284
BOXER BHL-225 Manual preview
BHL-225
Бренд: BOXER Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды