Daewoo EGSP-130E Скачать руководство пользователя страница 48

Страница: 48 / 55

Procedure

Test Program

Test Program Procedure

00: Power up and stand by

01: Open inlet valve, inlet water till the water level pressure
switch act and continue inletting water for 15 sec.

02: Start washing pump, check water level pressure switch. If the

switch reset, inlet supplementary water until switch act, and

then continue washing for 13 sec.

03: Open dispenser for 60 sec.

04: Run washing pump and heater until water temperature reached

05: Run drain pump till water level pressure switch reset, and

06: Pause for 15 seconds.

08: Run washing pump to wash for 3 minutes.

07: Open inlet valve till water level pressure switch act, and

11: Run drain pump till water level pressure switch reset, and
continue draining for 15 sec.

12: Buzz one sound, and then the machine stops.

10: Run washing pump to wash for 3 minutes.

09: Pause for 5 seconds.

Initialization

Inlet valve

Washing pump

Heating element

Drain pump

Pause

Inlet valve

Washing pump

Drain pump and

Regeneration

valve

Finish

Washing pump

Pause

Dispenser

Содержание EGSP-130E
























































Результаты поиска

Содержание EGSP-130E

Отзывы:

Похожие инструкции для EGSP-130E

Бренды по названию

Популярные бренды

Daewoo EGSP-130E, Техническое и сервисное руководство

Результаты поиска

Содержание EGSP-130E

Отзывы:

Похожие инструкции для EGSP-130E

Бренды по названию

Популярные бренды