Daewoo D1146 Скачать руководство пользователя страница 71

Страница: 71 / 147

D1146/D1146TI/DE08TIS

MAINTENANCE MANUAL

Printed in Jan. 2001 PS-MMA0415-E1A

2) Clearance

Measure the clearance between the

piston pin and connecting rod bushing,

and replace either of them, whichever

damaged more, if the measured value is

beyond the limit.

Standard Limit

0.003

∼

0.015 mm

0.08 mm

3) Condition check

Check the engaged condition of the

piston and piston pin. If it is possible to

force the pin into the piston heated with

piston heater, the piston is normal. When

replacing the piston, be sure to replace

the piston pin together.

(5) Connecting rod inspection

1) Distorsion

Check the connecting rod for distortion.

As shown in the figure below, install the

connecting rod to the connecting rod

tester, and check for distortion using a

feeler gauge. If the connecting rod is

found distorted, never re-use it but

replace with a new one.

2) Holes alignment (parallelism)

Measure the alignment of the

connecting rod piston pin bushing holes

with connecting rod big end holes. At

this time also, use both connecting rod

tester and feeler gauge.

Standard Limit

0.05 mm

0.1 mm or less

M1106

M1107

feeler gauge

Содержание D1146




















































































































































Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды

Daewoo D1146, Руководство по обслуживанию

Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды