Daewoo D1146 Скачать руководство пользователя страница 64

Страница: 64 / 147

D1146/D1146TI/DE08TIS

MAINTENANCE MANUAL

Printed in Jan. 2001 PS-MMA0415-E1A

In case that pin's wear is more than

the limit value, grind the crankshaft

journal and crank pin, and use the

undersized bearings.

Be sure to use grinding paper which

has been immersed in oil.

<Undersize bearings available>

Standard

0.25 (Inside diameter is 0.25 mm

lesser than the standard size.)

0.50 (Inside diameter is 0.50 mm

lesser than the standard size.)

0.75 (Inside diameter is 0.75 mm

lesser than the standard size.)

1.00 (Inside diameter is 1.00 mm

lesser than the standard size.)

Undersize bearings are available in 4

different sizes as indicated above, and the

crankshaft can be reused through the

regrinding as described above.

CAUTION :

In case of regrinding, the grinding the "R" part of bearing end should

be correctly done and keep in mind to remove any jaws or coarse

surface absolutely.

3) Crankshaft run-out

Support the crankshaft on V blocks.

Turn the crankshaft with a dial

indicator placed on the surface plate

and take the amount of crankshaft

run-out.

Standard Limit

0.05 mm

0.1 mm

"R" part's specified value

①

Crank pin's "R" : 4.5

−

②

Crank Journal "R" : 4

−

Содержание D1146




















































































































































Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды

Daewoo D1146, Руководство по обслуживанию

Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды