Daewoo D1146 Скачать руководство пользователя страница 42

Страница: 42 / 147

D1146/D1146TI/DE08TIS

MAINTENANCE MANUAL

Printed in Jan. 2001 PS-MMA0415-E1A

3.1.20. Fuel injection nozzle

Unscrew the fuel injection pipe between

the injection pump and nozzle and take

off the pipe.

Install a special jig on the nozzle holder,

and then pull out the nozzle as striking

the hammer of the jig backwardly.

Take care not to damage the nozzle

at disassembly.

Take out the seal ring from the nozzle

hole of the cylinder head and discard it.

3.1.21. Turbo charger (D1146TI, DE08TIS)

Remove the oil supply pipe and oil return

pipe between the turbo charger and the

cylinder block.

Unclamp the rubber hose connected the

intercooler and air cleaner.

Unscrew the turbo charger fixing nuts and

take off the turbo charger from the

exahust manifold.

3.1.22. Exhaust manifold

Unscrew the exhaust manifold fixing nuts

and remove the heat shield from the

exhaust manifold.

Then disassemble the exhaust manifold

and gasket.

Scrap the used gasket.

Содержание D1146




















































































































































Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды

Daewoo D1146, Руководство по обслуживанию

Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды