Daewoo D1146 Скачать руководство пользователя страница 124

Страница: 124 / 147

D1146/D1146TI/DE08TIS

MAINTENANCE MANUAL

119

Printed in Jan. 2001 PS-MMA0415-E1A

5) Reassembly

After removing carbon deposit, submerge the nozzle in diesel oil and clean it.

Replace all the seal rings with new ones.

Assemble the parts and tighten them to specified torque.

6) Adjustment

After reassembly, install the nozzle

on a tester.

With the adjusting screw loosened,

operate the nozzle 2

∼

3 times to

bleed it.

Operate the nozzle tester lever at

the specified rate.

Adjust the injection pressure to the

standard pressure by spring

tension shims.

After adjusting the injection

pressure, tighten the cap nut to

specified torque.

Re-check the injection pressure

and see if the spray pattern is

normal. Spray pattern should be

uniform and free of spattering.

7) Testing

With the nozzle assembled to a nozzle

tester and specified pressure applied,

check the nozzle for fuel leakage.

Engine Model

D1146

D1146TI

DE08TIS

Opening pressure

210 kg/cm

214

kg/cm

1st : 160 kg/cm

2nd : 220 kg/cm

Abnormal

Normal

Abnormal

Содержание D1146




















































































































































Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды

Daewoo D1146, Руководство по обслуживанию

Результаты поиска

Содержание D1146

Отзывы:

Похожие инструкции для D1146

Бренды по названию

Популярные бренды