background image

1

Important Information About 

Safety Instructions

•  The 

Important Safety Instructions

 and warnings in this 

manual cannot cover all possible issues. Use common 

sense and caution when installing the hood.

•  Contact Dacor Customer Assurance about issues you 

cannot resolve (contact information on previous page).

Important Safety Instructions

Safety Symbols and Labels

 DANGER

Immediate hazards that 

WILL

 result in severe personal 

injury or death.

 WARNING

Hazards or unsafe practices that 

COULD

 result in severe 

personal injury or death.

 CAUTION

Hazards or unsafe practices that 

MIGHT

 result in minor 

personal injury or property damage.

 DANGER

To avoid the possibility of explosion or fire, do not store or use combustible, flammable or explosive vapors and liquids 

(such as gasoline) inside or in the vicinity of this or any other appliance. Also keep items that could explode, such as 

aerosol cans away from cooktop burners, ovens and range hoods. Do not store flammable or explosive materials in 

adjacent cabinets or areas.

 WARNING

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal 

injury or death.

 WARNING

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE 

FOLLOWING:

a)  Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b)  Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means 

to prevent power from being switched on accidentally. When the service disconnecting means cannot be 

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

 WARNING

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE 

FOLLOWING:

a)  Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable 

codes and standards, including fire-rated construction. 

b)  Sufficient air is needed for proper combustion and exhausting of gases through the flue(chimney) of fuel 

burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety 

standards such as those published by the National Fire Protection Association (NFPA), and the American 

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

c)  When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d)  Ducted fans must always be vented to the outdoors.

READ AND SAVE THESE INSTRUCTIONS

Содержание HWHE30

























Отзывы: