Dacor CM24T, Руководство по установке

Страница: 6 / 16

p
lannIng the
I
nstallatIon
l
ocatIon
r
equIrements
• Dacor
®
cannot be held responsible for damage to
property or injury to persons caused by failure to
comply with the installation, maintenance, and safety
instructions contained in this handbook.
• Statutory regulations and the connection specifications
issued by the local power supply company must be
strictly observed.
• The coffee system is supplied with a 60” (1524mm)
long power cord terminated by a three-prong plug. The
power cord is intended to be plugged directly into a
dedicated, wall-mounted electrical receptacle.
• The correct voltage, frequency, and amperage must be
supplied to the electrical receptacle from a grounded,
dedicated, single phase circuit that is protected by a
properly sized circuit breaker or time-delay fuse. If one
is not installed, call a licensed electrician.
• The coffee system must be installed at a safe distance
from other sources of heat, such as home appliances,
in order to avoid an excessive rise in temperature.
• For ventilation purposes, there must be a slot near the
top of the cabinet back. The minimum dimensions are
4” X 12” (10.0 X 30.0cm).
NOTES:
1. The electrical box and water shut off valve (for model
CM24P) should be located in an adjacent cabinet.
2. The electric cord is located in the lower right rear
corner on the back of the unit.
3. To connect the water supply to a hose, you will need a
hose fitting with a 1/4-19 BSPP female thread.
4. Do not install the unit in a free-standing cabinet.
5. To prevent damage to the control panel door, do
not set the appliance on the floor or counter prior to
installation.
d
etermIne
W
ater
h
ardness
Before installing the coffee system, determine the water
hardness level by doing one of the following:
• Use the water hardness test strips included with the
appliance to test the water hardness level of the water
supplied to the building where the coffee system will be
installed. Dip the strip in a cup of water from a faucet
and read the hardness level according to the color key
included with the test strips.
• Call the local water company. Ask them for the water
hardness level of the water supplied to the building
where the coffee system will be installed.
For Model CM24T (Tank Model):
• If the water hardness level is above four grains per
gallon (4 gpg) you must use filtered water with a
hardness of 4 gpg or less. Do not use distilled water.
• If the water hardness level is below 4 gpg, you may
use tap water in the coffee system. Filtered water is
recommended for better taste.
For Model CM24P (Plumbed Model):
• If the water hardness is above 4 grains per gallon
(4gpg) contact a water treatment specialist. Have a
water treatment system installed that lowers the water
hardness level to 4 gpg or less.
• Regardless of the type of water treatment system
installed, Dacor highly recommends installation of
a Dacor ACFS flushing system (not included) with
model CM24P. The coffee system requires periodic
decalcification regardless of the water hardness level.
The filter head included in the flushing system kit is
required to perform this process for model CM24P.
• Attach the included bypass module to the filter head. If
the water supply to the filter head is unfiltered, you may
attach the optional filter cartridge (Dacor P/N ACWF)
instead to improve water taste. To prevent leaks over
time,
DO NOT use the JT-2 flushing cartridge for
everyday use.
Dacor ACFS flushing system kit installation.
Install for model CM24P.
Bypass Module
Filter Head
To coffee system To house water
supply or whole
house water filter
Installation of optional filter cartridge kit for model
CM24P with a water supply having no existing filter
system.
Optional Filter
Cartridge
(Dacor P/N ACWF)
Filter Head
To coffee system
To house
water supply