background image

28

Change the value by using [Dn Arrow] or [Up Arrow] or digits

[C]-delete

[OK]-for confirmation

[ESC]-for exit from the menu

5.Screen #5-setting of the 

Timer by pressing the [Timer] button twice

Row1: The number of the chosen timer

Setting of the time range of the timer

Row2: Setting of the time range of the timer in 15 minutes

Edit by pressing the [OK] button

Put “>” before the hour and minutes

Change the value by using [Dn arrow]  or [Up arrow] or digits

[C]-delete

[OK]-for confirmation

[ESC]-for exit from the menu

6.Screen #4 -setting of the Timer2 by pressing the [Timer] button 3 times

Timer.              Disabl

                     13:15:12

Timer.              Disabl

                    [ 13]:15:12

Timer.              Disabl

                     13:[15]:12

Timer 1                                Adjust

                  From-11:15   To -16:30

Timer 1                         Adjust

From  

> 05 

: 15  To-    08: 30

Timer 1                         Adjust

From

05  >  

15

   To-   08:  30

Timer 1                         Adjust

From

-      05

:15 To-  08  

>30

Timer 1                         Adjust

From     

>   05

:15 To  

>  08

:30

Содержание PG25CSH






























Отзывы: