manualshive.com logo in svg

Dabos PG25CSH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Dabos PG25CSH Скачать руководство пользователя страница 16

28

2. Basic display, mode”On”, it is switched on when you press [Stop] button.

Row 1: Boiler temperature sensor reading - of 27 ºC mode “On”.

If no sensor is connected or sensor reading is over 99 ºC - “no” inscription is 
displayed– operation is disabled.

If sensor is short circuited - “sc” inscription is displayed – operation is 
disabled.

“f” -indication for flame

-if the flame is stable the symbol 

”^”

 is displayed

-if the flame is weak, the symbol 

“!”

 is displayed

-if there is no flame, the position is blank

“p”-

 

indication of the status of the pump

-if it is switched on, the symbol  

” P”

 is displayed

- if it is switched off, the symbol  

” p”

 is displayed

“i”-indication for the ignition heater

-if it is switched on, the symbol  

” H”

 is displayed

- if it is switched off, the symbol  

”.”

 is displayed

“a”-indication for the auger transporter

-if it is switched on, the symbol  

” S”

 is displayed

- if it is switched off, the symbol  

” s”

 is displayed

“f”-indication for the fan

-if it is switched on, the symbol  

” F=xx”

 is displayed/x is the symbol for the 

degree of fan rates/

- if it is switched off, the symbol  

” f=”

 is displayed

T 27

°

C   fpiafb =99  Pow:Y

Start                13:15           

Содержание PG25CSH






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды