D-Link GO-DSL-AC750 Скачать руководство пользователя страница 130

Страница: 130 / 131

125

D-Link Wireless AC Dual-Band ADSL Router User Manual

Appendix D - Technical Specifications

Technical Specifications

General

Device Interfaces

• 802.11 ac/n/g/b Wireless LAN

• Four 10/100/1000 Gigabit LAN ports

• RJ-11 ADSL port

• USB 2.0 port

ADSL Standards

• ADSL 2+ Standards

• ITU-T G.992.5 Annex A/J

• ADSL 2 Standards

• ITU-T G.992.3 (G.dmt.bis) Annex A/J

• IUU-T G992.4 (G.lite.bis)

• ADSL Stadards

• Full-rate ANSI T1.413 Issue 2

• ITU-TG.992.1 (G.dmt) Annex A

• ITU-TG.992.2 (G.lite) Annex A

• ITU-T G.994.1 (G.hs)

ATM/PPP Support

• Multiprotocol over AAL5 (RFC 1483/2684)

• Bridged and routed Ethernet encapsulation

• LLC encapsulation

• VC-based multiplexing

• ATM Forum UNI3.1/4.0 PVC (up to 8 PVCs)

• ATM Cell Format ITU-T Rec. I.361

• ATM Adaption Layer Type 5 (AAL5)

• PPPoA (RFC2364)

• PPPoE (RFC2516)

• PPP Link Control Protocol (RFC 1661)

• Internet Protocol Control Protocol (RFC 1332)

• PPP Authentication Protocol (RFC 1334)

• PPP Challenge Handshake Authentication Protocol (RFC 1994)

• Microsoft PPP CHAP extensions (RFC 2433)

WLAN Specifications

• 802.11 n/g/b, up to 150 Mbps

• Wi-Fi Protected Setup (WPS)

• Multiple SSIDs

• Automatic rate adapting

• WAN scheduling

• Auto channel selection

• WMM support

• 64-bit & 128-bit WEP

• WPA-PSK & WPA2-PSK

• MAC address filtering

Network Services

• IPv4

• DHCP server/client/relay

• DNS relay

• Dynamic DNS (DDNS)

• Routing Information Protocol (RIP) v1/v2

• NAT AGLs

• PPTP

• L2TP

• FTP

• RTSP (RealTime Streaming Protocol)

• SIP v1/v2

• IPsec

• Internet Control Message Protocol (ICMP)

• Virtual server (Port forwarding)

• Simple Network Time Protocol (SNTP)

• 802.1d MAC Bridge (up to 256*8 MAC addresses)

• QoS

• IPP/ToS

• DSCP QoS in 4-priority queues

• Application QoS in 4-priority queues

• Strict priority

• VLAN QoS in 4-priority queues

• QoS remarking based on IPP/ToS, DSCP and 802.1p

• TOS transparency through NAT

• Mapping to queue according to DSCP bits and physical port

• 802.1Q

• IGMP proxy v1/v2

• IGMP snooping v1/v2/v3

Standards

• IEEE 802.11ac

• IEEE 802.11n

• IEEE 802.11g

• IEEE 802.11b

• IEEE 802.3

• IEEE 802.3u

Minimum System Requirements

• Windows 8/7/Vista/XP SP3 or

Mac OS X 10.4 or higher

• Microsoft Internet Explorer 6 or higher, Firefox 1.0 or higher, Safari 1.2 or higher,

or other Java-enabled browser

• Ethernet network interface

• Cable or DSL modem

• Subscription with an Internet Service Provider (ISP)

Содержание GO-DSL-AC750




































































































































Результаты поиска

Содержание GO-DSL-AC750

Отзывы:

Бренды по названию

Популярные бренды

D-Link GO-DSL-AC750, Руководство пользователя

Результаты поиска

Содержание GO-DSL-AC750

Отзывы:

Бренды по названию

Популярные бренды