D-Link DVG-7111S Скачать руководство пользователя страница 5

Страница: 5 / 95

DVG-7111S

User’s Manual

Telephone Interface Description

D-Link Systems, Inc.

1-2 Hardware Description

Front Panel



Power:

Solid green light indicates a normal power supply.



Alarm:

Red light indicates abnormal status, such as failed to register or provision or not obtained IP

address.



Register:

The Register LED will turn on when the VoIP Router is connected to a VoIP service

provider. The LED will blink if not connected to a service provider.



LAN indicator:

When a connection is established the LED will light up solid. The LEDs will blink to

indicate activity. If the LED does not light up when a cable is connected, verify the cable
connections and make sure your devices are powered on.



WAN indicator:

When a connection is established the LED will light up solid. The LED will blink to

indicate activity. If the LED does not light up when a cable is connected, verify the cable
connections and make sure your devices are powered on.



Phone Indicator:

Phone LED will light up solid if a phone connected to a phone port is off the hook

or in use. When a phone is ringing, the indicator will blink.



Line Indicator:

Line LED light on means FXO/PSTN line is in use (off-hook).

Note: When starting up DVG-7111S, all indicators will light up. After about 40 seconds, the Reg.

indicator will blink in green. If the Prov./Alm indicator continues to blink, it means DVG-7111S is
currently communicating with ISP and has yet to obtain an IP address or fail to register to VoIP
Service Provider.

Содержание DVG-7111S
































































































Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды

D-Link DVG-7111S, Руководство пользователя

Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды