D-Link DVG-7111S Скачать руководство пользователя страница 28

Страница: 28 / 95

DVG-7111S

User’s Manual

SETUP

D-Link Systems, Inc.

Lease Time:

Enter the length of time for the IP lease.

Domain Name Server Assignment:

Select

Auto

Manual

to get the IP address of Domain Name

Server assigned by ISP or manually.

Domain Name Server IP:

Enter the primary and secondary IP address of Domain Name Server if

Domain Name Server Assignment is

Manual

. Otherwise, the VoIP TA will not be able to access hosts

using hostnames instead of IPs.

SETUP

→

LAN Setup

Enable Port:

It is to active/des-active LAN port physical connection.

Incoming Rate Limit:

Set the incoming (from LAN to WAN) rate limit of a specific LAN port (can not

exceed the real downstream bandwidth).

Outgoing Rate Limit:

Set the outgoing (from WAN to LAN) rate limit of a specific LAN port (can not

exceed the real upstream bandwidth).

NAT/Bridge:

Select the VoIP Router serving as a

Router

with NAT or

Bridge

between WAN port and

LAN port without NAT.

Note:

If you set a LAN port to be bridge mode that the LAN port will be bundled with WAN. If you

would like to connect to DVG-N5412SP at the bridged LAN port you must enter WAN port IP.

VLAN ID:

Assign a VLAN ID for DVG-N5412SP to transit traffic through-out at WAN port for WAN-LAN

bridge mode. The packets are un-tagged at LAN port and added tag at WAN port.

Note:

It is not allowed to change VLAN ID for NAT mode LAN ports. The VLAN ID of NAT LAN

ports are bundled with WAN 1 which assigned at Internet Setting page. The packets are un-tagged
at LAN port and added tag at WAN port.

Содержание DVG-7111S
































































































Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды

D-Link DVG-7111S, Руководство пользователя

Результаты поиска

Содержание DVG-7111S

Отзывы:

Похожие инструкции для DVG-7111S

Бренды по названию

Популярные бренды