D-Link DVG-7111S Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 95

background image

DVG-7111S

User’s Manual

SETUP

D-Link Systems, Inc.

25

SETUP

→

VoIP Setup

Outbound Proxy Support:

Check the box to send all SIP packets to the destined outbound proxy

server. An outbound proxy server handles SIP call signaling as a standard SIP proxy server would do.
Further, it receives and transmits phone conversation traffic (media) between two communication
parties. This option tells the VoIP TA to send and receive all SIP packets to the destined outbound
proxy server rather than the remote VoIP device. This helps VoIP calls to pass through any NAT
protected network without additional settings or techniques. Please make sure your VoIP Service
Provider supports outbound proxy services before you enable it.

Outbound Proxy IP/Domain:

Enter the outbound proxy

’s IP address or URL.

Outbound Proxy Port:

Enter the outbound proxy

’s listening port.

SETUP

→

VoIP Setup

Enable P-Assert:

Check the box to enable the caller ID protection.

Privacy Type:

It is used to disguise the caller ID when queried via an VoIP Service Provider/Third-Party

Assertion. The Privacy Type includes

‘user’, ‘header’, ‘session’, ‘none’, ‘critical’, ‘id’ and ‘history’.

SETUP

→

VoIP Setup

The rule of dialing of inviting to VoIP Service Providers may vary. That is, you have to configure
different Digit Map for different VoIP Service Providers. In this filed, you can configure individual dialing
plan for each VoIP Service Provider. The following examples introduce some cases. For general
configuration, refer to

Digit Map

page.

Note: Press

“Add” to add an entry. Don’t forget to press “Apply” which in the above of Number

Translation.

«
...
23
24
25
26
27
...
»

Содержание DVG-7111S
































































































Отзывы:

Нет отзывов

Похожие инструкции для DVG-7111S

Бренд: Parker Страницы: 36

Бренд: Sena Страницы: 25

Бренд: Emos Страницы: 24

KAT Walk C PiSystem Adapter

Бренд: KAT VR Страницы: 12

WAB501 - 802.11a/b Dual Band PC Card

Бренд: NETGEAR Страницы: 17

Бренд: SMC Networks Страницы: 18

Бренд: 3idee Страницы: 8

Бренд: Eskridge Страницы: 4

Бренд: KTI Networks Страницы: 24

Бренд: Belkin Страницы: 25

Stylus COLOR 3000

Бренд: Epson Страницы: 1

USBw 100 Series

Бренд: Motorola Страницы: 55

Бренд: Motorola Страницы: 187

Бренд: Crown Страницы: 65

Бренд: Clarity Страницы: 8

Бренд: Choetech Страницы: 38

Бренд: EnGenius Страницы: 45

Бренд: Planet Networking & Communication Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды